Adastra AT6 Bedienungsanleitung

Adastra Lautsprecher AT6

Lies die bedienungsanleitung für Adastra AT6 (4 Seiten) kostenlos online; sie gehört zur Kategorie Lautsprecher. Dieses Handbuch wurde von 29 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 15 Bewertungen. Hast du eine Frage zu Adastra AT6 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

AT6

6-Zone 100V Attenuator & Source Selector

Item ref: 2.476 95 UK

User Manual

Version 1.0

Caution: Please read this manual carefully before operating

Damage caused by misuse is not covered by the warranty

952.476UK User Manual

Introduction

Thank you for choosing the Adastra AT6 attenuator and source selector as part of your public address system.

This unit is designed to offer a completely passive zone control ution for installed 100V public address systems. sol

Please read this manual to gain the best results from your product and avoid damage through misuse.

SAFETY SYMBOL AND MESSAGE CONVENTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC

ELECTRIQUE NE PAS

OUVRIR

This symbol indicates that dangerous voltage constituting a risk of

electric shock is present within this unit

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

Important not e: ic

The AT6 is designed for 100V speaker systems and is not suitable for low impedance 4/8/16 speakers. Ω

Although not mains powered, the 100V rating of this product requires standar high voltage precautions to be observed. d

Take care when making connections to avoid any shorted wires, which could cause damage to the amplifiers or the AT6.

Each output of the AT6 has a maximum power rating of 30W. Ensure that the combined tapped power of speakers

connected to a single output do not exceed 30W. es

Safety

• If liquids are spilled on the casing, stop using the AT6 immediately, allow the unit to dry out and have checked by

qualified personnel before further use.

• Avoid impact, extreme pressure or heavy vibration to the case

• No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –

• Use double insulated speaker wire with adequate current rating for the 100V speaker connections

Placement

• Keep out of direct sunlight and away from heat sources

• Keep away from damp or dusty environments

• Ensure adequate access to controls and connections

Cleaning

• Use a soft cloth with a neutral detergent to clean the casing as required

• Do not use strong solvents for cleaning the unit

Installation

The AT6 may be installed into a standard 1U rack space in a 19 rack cabinet. ”

Alternatively, the AT6 may be used free-standing.

Ensure adequate support for the unit and access connectors, terminals and controls. to

Do not place heavy objects on top of the AT6 that may cause excessive strain on the housing.

952.476UK User Manual

Front panel

Zone volume rotary switch controls

Source select (amplifier A / amplifier B)

Zone on/off switch

Rear panel

Zone output 6 screw terminals - + /

Zone output 1 screw terminals - + /

Zone output 5 screw terminals + / -

1 0.

Amplifier input B screw terminals + / -

Zone output 4 screw terminals - + /

11.

24V emergency mute screw terminals + / -

Zone output 3 screw terminals - + /

12.

Amplifier input A screw terminals - + /

Zone output 2 screw terminals + / -

Connection and setup

Connections for the AT6 are all on the rear panel and the screw terminals are on removable blocks

for ease of installation. Ensure all connection polarities are correct as indicated on the rear panel.

The AT6 can operate in conjunction with one or two 100V amplifiers as input sources.

Connect the 100V output terminal from amplifier to the + terminal of IN A on the AT6 (12) an “ ”

Connect the COM output terminal from the same amplifier to the - terminal of IN A on the AT6. “ ”

If another amplifier is to be used as a second source, repeat the above steps for IN B terminals (10).

Between the terminals for IN A and IN B are another pair of screw terminals labelled EMG 24V (11) “ ”

These may be connected to the 24V trigger of an emergency panel to mute all outputs upon alarm.

Take maximum care not to allow any shorted strands of wire across any of the terminals.

All 100V speaker outputs are via screw terminals on 2 further removable blocks (4 –9)

Connect 100V speakers via the corresponding + and - output terminals on the AT6 “ ” “ ”

If more than 1 speaker is to be connected to a single zone output, connect these in parallel.

Ensure that the total load of all speakers on a single output does not exceed 30W.

Make sure all screw terminal blocks are firmly in place on the rear panel after making connections.

Produktspezifikationen

Marke:	Adastra
Kategorie:	Lautsprecher
Modell:	AT6
Breite:	482 mm
Tiefe:	160 mm
Gewicht:	2390 g
Produktfarbe:	Schwarz
Impedanz:	- Ohm
Höhe:	43 mm
Stecker:	IN A + B, OUT 1-6, 24V MUTE (Euroblock screw terminals)
Verpackungsbreite:	470 mm
Verpackungstiefe:	190 mm
Verpackungshöhe:	90 mm
Paketgewicht:	2600 g
Frequenzbereich:	- GHz
Maximale Eingangsleistung:	30 W