Advance Tabco DI-1-30 Bedienungsanleitung
Advance Tabco
Spülbecken
DI-1-30
Lies die bedienungsanleitung für Advance Tabco DI-1-30 (2 Seiten) kostenlos online; sie gehört zur Kategorie Spülbecken. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Advance Tabco DI-1-30 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
EDGEWOOD, NY 11717-8380
INSTALLATION INSTRUCTIONS for
DROP-IN SINKS
CHECK FOR CONCEALED DAMAGE
FILE CLAIM WITH FREIGHT CARRIER
Drop-ins manufactured by ADVANCE TABCO are designed and constructed for
countertop installations. Only one compartment units intended for HAND SINK USE
are NSF listed and approved. Suggested end use for drop-in sinks include dump
sinks, bar sinks, wash sinks and hand sinks.
STEP 5
• Remove masking tape from counter
surface and position sink into opening to
ensure proper fit.
STEP 6
• Remove sink from opening and apply 1/4”
bead sealant along edge of cut out.
• Install sink into counter top.
• Insert slotted end of screw thru clearance hole in clip and secure
by turning Counter-Clockwise.
• Slide clip into end of Roll Form track (As
Shown) and position where desired and
hand tighten. Once all clips are in position,
tighten with screwdriver -
DO NOT OVERTIGHTEN!
• Wipe excess Silicone from counter
surface.
STEP 7
• Connect Drain and Faucet supply lines.
C
L
Faucet
Removable Aerator
Plastic Gasket
Lock Nut
Metal Washer
Supply Line
STEP 4
• Install Faucet (as shown).
© ADVANCE TABCO, SEPTEMBER 2018
STEP 1
Remove all contents from carton.
(NOTE: Check for concealed damage - Notify Carrier of any
damages immediately)
STEP 2
• Position sink (upside down) onto counter top surface at
desired location. Trace outer edge of Self-Rim with pencil.
(NOTE: Ensure sink is parallel to counter edges. Procedure
does not apply to DI-1-30, DI-1-5SP or DI-1-10SP.
Refer to chart for Cut Out dimensions.)
• Remove sink and draw a second line 3/8” parallel to
the inside of the marked line - that will be the CUT line
(As shown).
• NOTE: BEFORE CUTTING
COUNTER TOP, REFER TO THE
CHART TO VERIFY CUTOUT
DIMENSIONS!
REMEMBER:
MEASURE TWICE, CUT ONCE!
• Drill 1/4” hole 1 to the inside of cut line then use 1/2” drill bit
to enlarge hole.
• Apply masking tape along outer (sink edge) line. This will
prevent damaging countertop while cutting.
• Position jig saw blade into 1/2” hole and follow CUT LINE.
Rubber Washer
Fiber Washer
Die Cast Nut
STEP 3
• Install Drain -
Apply a bead of
Plumber’s Putty
as shown.
1/4” continuous bead of
Plumber’s Putty.
<< CORRECT MARKING
PROCEDURE
Pencil MUST be held
straight as possible.
INCORRECT >>
MARKING
PROCEDURE
3/8
Equipment that includes a faucet may expose you to chemicals, including lead,
that are known to the State of California to cause cancer or birth defects
or other reproductive harm. For more Info.,visit www.p65warnings.ca.gov.
WARNING:
This Carton Contains:
1 ea. Sink Bowl
Basket Type Drain sub assembly (See chart).
Faucet sub assembly (See chart).
Mounting Clips* (See chart).
LENGTH IS LEFT TO RIGHT
WIDTH IS FRONT TO BACK
LENGTH IS LEFT TO RIGHT
WIDTH IS FRONT TO BACK
SCH-2317
SCH-1-2517L
SCH-1-2517R
16” x 14” x 7 1/2”
16” x 14” x 7 1/2”
16” x 14” x 7 1/2”
23” x 17”
25” x 17”
25” x 17”
22 1/4” x 16 1/4”
24 1/4” x 16 1/4”
24 1/4” x 16 1/4”
1 1 8 16 lbs.
3 1 12 18 lbs.
1 3 12 18 lbs.
Bowl Dim. O.A. Dim. Cutout Size Ship
MODEL #
L x W
L x W
1 1/4” Radius Weight
Faucet Holes
Left Right
LENGTH IS LEFT TO RIGHT
WIDTH IS FRONT TO BACK
TOOLS REQUIRED:
• Drill Motor
• 1/4” - 1/2” Drill Bits
• Long Shank Screw Driver
• Ruler or Tape Measure
• Pencil
• Adjustable Wrenches (2)
• Pipe Wrench
• Saber Saw or Jig Saw
MATERIAL REQUIRED:
• Silicone Sealant
• Plumbers Putty
• Masking Tape
RECOMMENDED SAFETY MATERIALS:
• Safety Glasses
• Work Gloves
NOTE:
The corners of ALL Cutouts are to have
a 1-1/4” Radius.
SMART SERIES
™
SMART SERIES
™
For the Classroom
# Clips
U Channel
Installation
U Channel
Installation
ABOVE SINKS SUPPLIED WITH K-52 GOOSENECK FAUCET UNLESS NOTED.
†† SUPPLIED WITH WATER FILLER FAUCET & GRATING
*SUPPLIED WITH K-50 FAUCET **SUPPLIED WITH K-53 FAUCET WITH 12” SPOUT
***SUPPLIED WITH K-51 FAUCET WITH 6” SWING SPOUT
NOTE: DBS SERIES DRAINS ARE LOCATED AT THE LEFT REAR CORNER.
EACH BOWL INCLUDES 8 9/16” OVERFLOW PIPE WITH 1 1/2” IPS DRAIN.
U Channel
Installation
FAUCETS OPTIONAL
FAUCETS OPTIONAL
Faucet &
Bubbler
Optional
MODEL #
Bowl Dim.
L x W x D
Overall
Dim.
Cutout Size
1 1/4” Radius
Faucet
# Drains
# Clips
Ship
Wt.
*** DBS-1 10” x 14” x 10” 13” x 19” 12 1/4” x 18 1/4” 1 1 8 11 lbs.
DI-1-5 10” x 14” x 5” 13” x 19” 12 1/4” x 18 1/4” 1 1 8 9 lbs.
DI-1-5SP 10” x 14” x 5” 13” x 19” 12 1/4” x 18 1/4” 1 1 4 13 lbs.
†† DI-1-9 9” x 9” x 3” 12” x 14” 11 1/4” x 13 1/4” 1 1 8 8 lbs.
DI-1-10 10” x 14” x 10” 13” x 19” 12 1/4” x 18 1/4” 1 1 8 11 lbs.
DI-1-10SP 10” x 14” x 10” 13 x 19” 12 1/4” x 18 1/4” 1 1 4 18 lbs.
DI-1-1515
12-1/4” x 10”-1/4 x 6”
15 x 15” 14 1/4” x 14 1/4” 1 1 8 11 lbs.
DI-1-25 9” x 9” x 5” 12” x 14” 11 1/4” x 13 1/4” 1 1 8 8 lbs.
DI-1-30 14” x 10” x 5” 16” x 15” 15” x 14 1/4” 1 1 4 11 lbs.
DI-1-35 14” x 10” x 5” 17” x 15” 16 1/4” x 14 1/4” 1 1 8 8 lbs.
DI-1-168 16” x 14” x 8” 19” x 19” 18 1/4 ”x 18 1/4” 1 1 12 15 lbs.
* DI-1-208 20” x 16” x 8” 23” x 21” 22 1/4” x 20 1/4” 1 1 12 29 lbs.
* DI-1-2012 20” x 16” x 12” 23” x 21” 22 1/4 ”x 20 1/4” 1 1 12 25 lbs.
** DI-1-2812 28” x 20” x 12” 31” x 25” 30 1/4” x 24 1/4” 1 1 12 42 lbs.
*** DBS-2 10” x 14” x 10” 25 1/2” x 19” 24 3/4” x 18 1/4” 1 2 12 20 lbs.
* DI-2-10 10” x 14” x 10” 25 1/2” x 19” 24 3/4” x 18 1/4” 1 2 12 20 lbs.
* DI-2-1410 14” x 16” x 10” 33 1/2” x 21” 32 3/4” x 20 1/4v 1 2 12 33 lbs.
* DI-2-2012 20” x 16” x 12” 45 1/2” x 21” 44 3/4” x 20 1/4” 1 2 16 40 lbs.
* DI-2-208 20” x 16” x 8” 45 1/2” x 21” 44 3/4” x 20 1/4” 1 2 16 29 lbs.
** DBS-3 10” x 14” x 10” 38” x 19” 37 1/4” x 18 1/4” 1 3 16 32 lbs.
* DI-3-10 10” x 14” x 10” 38” x 19” 37 1/4” x 18 1/4” 2 3 16 32 lbs.
* DI-3-1410 16” x 14” x 10” 50” x 21” 49 1/4” x 20 1/4” 2 3 16 52 lbs.
** DI-3-1612 16” x 20” x 12” 56” x 25” 55 1/4” x 24 1/4” 2 3 16 60 lbs.
MODEL #
Bowl Dim.
L x W x D
Overall
Dim.
Cutout Size
1 1/4” Radius
Faucet
# Drains
# Clips
Ship
Wt.
S-1-1715-7 14” x 10” x 7 1/2” 17” x 15” 16 1/4” x 14 1/4” 1 1 8 12 lbs.
SS-1-1715-10 14” x 10” x 10” 17” x 15” 16 1/4” x 14 1/4” 1 1 8 14 lbs.
SS-1-1919-7 16” x 14” x 7 1/2” 19” x 19” 18 1/4” x 18 1/4” 1 1 12 16 lbs.
SS-1-1919-10 16” x 14” x 10” 19” x 19” 18 1/4” x 18 1/4” 1 1 12 18 lbs.
SS-1-1919-12 16” x 14” x 12” 19” x 19” 18 1/4” x 18 1/4” 1 1 12 20 lbs.
SS-1-2321-7 20” x 16” x 7 1/2” 23” x 21” 22 1/4” x 20 1/4” 1 1 12 20 lbs.
SS-1-2321-10 20” x 16” x 10” 23” x 21” 22 1/4” x 20 1/4” 1 1 12 22 lbs.
SS-1-2321-12 20” x 16” x 12” 23” x 21” 22 1/4” x 20 1/4” 1 1 12 25 lbs.
SS-2-3321-7 14” x 16” x 7 1/2” 33 1/2” x 21” 32 3/4” x 20 1/4” 1 2 12 33 lbs.
SS-2-3321-10 14” x 16” x 10” 33 1/2” x 21” 32 3/4” x 20 1/4” 1 2 12 35 lbs.
SS-2-3321-12 14” x 16” x 12” 33 1/2” x 21” 32 3/4” x 20 1/4” 1 2 12 37 lbs.
SS-2-4521-7 20” x 16” x 7 1/2” 45 1/2” x 21” 44 3/4” x 20 1/4” 1 2 12 38 lbs.
SS-2-4521-10 20” x 16” x 10” 45 1/2” x 21” 44 3/4” x 20 1/4” 1 2 12 39 lbs.
SS-2-4521-12 20” x 16” x 12” 45 1/2” x 21” 44 3/4” x 20 1/4” 1 2 16 40 lbs.
* Standard mounting clips fit counters 7/8” to 2” thick. For narrower countertops,
underside must be ‘built up’ (by others) to at least 7/8” thick. For thicker countertops,
end user will need to supply their own longer mounting screws as needed.
Produktspezifikationen
| Marke: | Advance Tabco |
| Kategorie: | Spülbecken |
| Modell: | DI-1-30 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Advance Tabco DI-1-30 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Spülbecken Advance Tabco
20 August 2025
20 August 2025
20 August 2025
10 Juni 2025
7 Februar 2024
5 Februar 2024
4 Dezember 2023
17 September 2023
24 August 2023
Bedienungsanleitung Spülbecken
- Signature Hardware
- Eagle Group
- Artusi
- Hendi
- Schock
- CDA
- Kohler
- Royal Catering
- Roca
- Leisure
- Rangemaster
- Sani-Lav
- Elkay
- Caple
- Krowne
Neueste Bedienungsanleitung für -Kategorien-
20 August 2025
18 August 2025
18 August 2025
18 August 2025
17 August 2025
17 August 2025
17 August 2025
16 August 2025
6 August 2025
6 August 2025