Aeon Labs Z-Stick Bedienungsanleitung

Aeon Labs Netzwerkkarte / Adapter Z-Stick

Lies die bedienungsanleitung für Aeon Labs Z-Stick (4 Seiten) kostenlos online; sie gehört zur Kategorie Netzwerkkarte / Adapter. Dieses Handbuch wurde von 51 Personen als hilfreich bewertet und erhielt im Schnitt 4.1 Sterne aus 26 Bewertungen. Hast du eine Frage zu Aeon Labs Z-Stick oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

Aeon Labs Z-Stick

(Z-Wave USB Adapter)

Introduction:

The Aeon Labs Z-Stick is a self-powered Z-Wave USB adapter with remote network creation

capabilities (independent from external power and host microprocessor). By being able to

remotely include/remove Z-Wave devices, this greatly simplifies Z-Wave network installation.

When connected to a host processor (via USB), it enables the host processor to take part in the

Z-Wave Network.

By taking advantage of the Z-Wave mesh network, commands can be routed to their

destination via intermediary “listening” Z-Wave products. Products that are Z-Wave certified

can be used and communicate with other Z-Wave certified devices.

Operating instructions:

The Z-Stick operates in three distinct modes: Inclusion-Mode, Removal-Mode and SerialAPI-

Mode. Both Inclusion-Mode and Removal-Mode require the Z-Stick to be unplugged from the

USB connector of the host, while SerialAPI-Mode requires that the Z-Stick to be plugged into

the USB connector of the host.

• Inclusion-Mode : Adding/Including Z-Wave Devices into the Z-Wave Network

1. To initiate Inclusion-Mode, unplug the Z-Stick from the USB connector and then tap the

button. (The LED will blink slowly.)

Note: While in Inclusion-Mode, the Z-Stick is in perpetual add/inclusion. There is no

need to press the button on the Z-Stick again to include each new device.

2. To include a new Z-Wave device into the network, simply go to the device with the Z-

Stick and press the button on the device you wish to include. (The LED on the Z-Stick

will blink fast during a network neighbor discovery and stay solid for 3 seconds to

indicate successful inclusion of the device into the network.)

3. The LED will then return to blinking slowly, indicating readiness for further device

inclusions. Repeat step 2 for each device as you wish to include.

4. Tap the Z-Stick button to turn it off.

• Removal-Mode : Deleting/Removing/Excluding Z-Wave Devices from the Z-Wave Network

1. To initiate Removal-Mode, unplug the Z-Stick from the USB connector. Then press and

hold down the button for approximately 3 seconds. (The LED will transition from

blinking slowly to blinking fast.)

Note: While in Removal-Mode, the Z-Stick is in perpetual removal/exclusion where it

will remove Z-Wave devices from the networks they are currently paired to. There is no

need to press the button on the Z-Stick again to exclude each device.

2. To remove a Z-Wave device from the network, simply go to the device with the Z-Stick

and press the button on the device you wish to remove. (The LED on the Z-Stick will

immediately stay solid for 3 seconds to indicate successful removal from the network.)

3. The LED will then return to blinking fast, indicating readiness for further device

exclusions. Repeat step 2 for each device as you wish to exclude.

4. Tap the Z-Stick button to turn off.

Produktspezifikationen

Marke:	Aeon Labs
Kategorie:	Netzwerkkarte / Adapter
Modell:	Z-Stick
Breite:	28 mm
Tiefe:	69 mm
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabellos
Höhe:	14 mm
Betriebstemperatur:	-35 - 85 °C
Maximale Datenübertragungsrate:	480 Mbit/s
Eingebaut:	Nein
Unterstützt Windows-Betriebssysteme:	Ja
Kabellose Reichweite:	30 m
Unterstützt Mac-Betriebssysteme:	Ja
Unterstützte Linux-Betriebssysteme:	Ja
Hostschnittstelle:	USB
USB:	Ja
Data Link Protokolle:	Zensys 5.02
Kanalabstand:	868.42 MHz