APC UXABP48 Bedienungsanleitung

APC Batterie UXABP48

Lies die bedienungsanleitung für APC UXABP48 (4 Seiten) kostenlos online; sie gehört zur Kategorie Batterie. Dieses Handbuch wurde von 40 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 20.5 Bewertungen. Hast du eine Frage zu APC UXABP48 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

UXBP

Battery Pack

Models: UXBP24, UXBP24L, UXABP48

• Do not move the UXBP with its batteries installed. Doing so may

result in damage to the Battery Pack and/or a shock hazard.

• Install only factory-authorized batteries in the UXBP. Improper

batteries may result in a hazardous chemical spill and/or a shock

hazard.

3. Presentation

3.1 UXBP front

UXBP Battery Pack

The UXBP contains either two (UXBP24L) or four (UXBP24,

UXABP48) user-replaceable, sealed lead-acid batteries and the associated

cables and connectors.

1. Front panel/Battery door

The front panel of the Battery Pack provides access for battery installation

and replacement. Refer to Section 4 when installing or replacing batteries.

2. Battery internal coupler

These four couplers connect the UXBP’s replaceable internal batteries. See

Section 4.

3. Batteries

The Battery Pack contains either two (UXBP24L) or four (UXBP24,

UXABP48) nominal 12 Vdc sealed lead-acid batteries. Use only factory-

authorized batteries in the UXBP!

3.2 UXBP rear

1. Battery Pack rear panel coupler

Additional UXBP Battery Packs are connected to this coupler. Refer to

Section 4.5 for information on making connections with this coupler.

2. In-line Battery Pack coupler

This coupler connects the Battery Pack to the UPS or to the rear panel

coupler on another matching Battery Pack.

1. Introduction

The UXBP is a large Battery Pack module designed to be used with a Smart-

UPS system to provide a significant increase in on-battery runtime for your

protected equipment.

For complete information on the Smart-UPS system, refer to the Owner’s

Manual that came with your UPS.

Note: If you are installing your Smart-UPS system for the first time, be

sure to read the Smart-UPS Owner’s Manual ﬁrst. Set up your

UPS system before installing the UXBP.

2. Safety!

CAUTION!

• Use the UXBP only with a UPS that is properly installed according to

the UPS Owner’s Manual and connected only to a two-pole, three-wire

grounding mains receptacle. The receptacle must be connected to

appropriate branch protection (fuse or circuit breaker). Connection to

any other type of receptacle may result in a shock hazard and may

violate local electrical codes.

• Avoid installing the UXBP in locations where there is water or

excessive humidity.

• Do not allow water or any foreign object to get inside the UXBP. Do

not put objects containing liquid on or near the unit.

• To reduce the risk of overheating the UXBP, avoid exposing the unit to

the direct rays of the sun. Avoid installing the unit near heat emitting

appliances such as a room heater or stove.

Installation Instructions

Produktspezifikationen

Marke:	APC
Kategorie:	Batterie
Modell:	UXABP48
Akku-/Batteriekapazität:	3360 mAh
Gewicht:	127270 g
Produktfarbe:	Schwarz
Akku-/Batterietechnologie:	Plombierte Bleisäure (VRLA)
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Paketgewicht:	142730 g
Zertifizierung:	RoHS
Warentarifnummer (HS):	85078000
Temperaturbereich bei Lagerung:	-15 - 45 °C
Luftfeuchtigkeit bei Lagerung:	0 - 95 %
Batteriekapazität:	3360 Ah
Abmessungen (BxTxH):	447 x 754 x 310 mm
Eingangsspannung:	48 V
Verpackungsabmessungen (BxTxH):	508 x 838 x 432 mm
Batterie Lebensdauer:	3 Jahr(e)
Höhe bei Betrieb:	0 - 3000 m