Artograph Prism Bedienungsanleitung
Artograph
videopprojektor
Prism
Lies die bedienungsanleitung für Artograph Prism (8 Seiten) kostenlos online; sie gehört zur Kategorie videopprojektor. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Artograph Prism oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
!
Mount the projector onto a surface that can be easily moved. Movement of the
projector is required to achieve the desired size. A taboret or rolling cart is ideal.
A
rtograph offers an optional Projector Floor Stand, item #225-350, that can be
easily moved and raised for the ultimate in image positioning.
PROJECTING
To load the projector, simply lift the copy board lid of
the projector and mount your copy face down onto the
g
lass surface. The metal copy clip may be pushed to
the side if desired as it is only necessary when
mounting the projector onto the accessory Prism Table
Stand, item #225-206. Close the cover, plug the projector
into an outlet and turn the projector on by flipping the
switch at the back of the unit. Turn the room lights off. You are
now ready to adjust the size and clarity of the projected image.
Always adjust the desired size of the projected image first before
focusing it. (See Distance Chart for
approximate distance.)
Caution: During operation, ensure the projector is
properly ventilated. Do not block the exhaust or inlet vents
located on the back and sides of the projector.
IMPORTANT
SAFEGUARDS
When using this projector, always follow basic
safety precautions, including the following:
1. Read and understand all instructions before operating.
2. Close supervision is necessary when used by or near children. Do not leave
unattended while in use.
3. Do not operate this equipment with a damaged cord, or if it has been dropped
or otherwise damaged, until it has been examined by a qualified electrician.
4. If an extension cord is necessary, be sure it has a suitable current rating.
Cords rated for less amperage than this equipment may overheat. Be
careful to arrange the cord so that it will not be tripped over or pulled.
5.
Always unplug from the electrical outlet when not in use. Disconnect by
grasping and pulling the plug from the outlet; never yank the cord to
disconnect the plug.
6. Allow the projector to cool completely before moving. Loop the cord loosely
when storing.
7. If the projector receives water damage, do not use until inspected by a
qualified electrician.
8. To avoid electrical shock hazard, do not disassemble. Take the projector
to a qualified electrician. Incorrect reassembly can cause an electrical
shock hazard.
PLEASE SAVE THESE INSTRUCTIONS
CONTENTS:
Projector + Prism lens
LENS
INSTALLATION:
The rubber “O” ring (#2) should
be rolled down to the end of the
lens that is sticking out of the
projector. This ring prevents the
lens from entering too far into the
lens barrel. (See General Focusing
& Enlarging section for reduction and
enlargement positions.)
PROJECTION AREA
All opaque projectors work like a flashlight; the darker the room, the brighter
the projected image will appear. The clearest and brightest images are
produced in a completely dark room. For best results, operate your Prism
in a room where you are able to control the lighting conditions or work in the
evening. To achieve the maximum image size of approximately 20X,
a minimum distance of 18 ft. (5.5m), measured from the label above
the lens to the projection surface, is required (see Distance Chart for
further information).
GENERAL FOCUSING & ENLARGING
The size and clarity of your projected image is determined
by the distance of the projector from the projection surface and the focusing of
t
he lens. The farther the projector is from the work surface, the larger your
image will be. As you change distance, you will have to slide the lens in or
out slowly within the lens barrel to focus the projected image.
The Prism both enlarges and reduces with one reversible lens. The
projection range of this lens is 80% (4/5 x) reduction (20% less than
t
he size of your original), up to 20 times enlargement. Please Note:
A gap exists in the projection range that cannot be achieved due to
the reversing of the lens –170% to 250%. You will have to adjust the
s
ize of your original to achieve
a size in this range.
Distance Chart (approximate) –
Measured from label above lens to projection surface.
Range .8 1x 5x 10x 20x
Distance 24” 23” 47” 89” 14’
(61cm) (58cm) (1.2m) (2.3m) (4.3m)
[Lens in reduction position] [Lens in enlargement position]
COPY AREA
T
he copy area is 7" x 7". This indicates the maximum
s
ize of copy the lens can
see. This copy size, however, varies with the desired projection size. With
greater enlargement, the lens sees less of the copy area.
PHOTOGRAPH PROJECTION
(USE CAUTION!)
P
hotographs are commonly used in projectors; however, a few precautions
must be taken:
1.
Work from a copy of any valuable or important photographs. Never
use an original if it cannot be replaced. Photographs were not intended to
handle the intense light and heat created by a projector. Though this
projector is fan-cooled and ventilated to keep the copy cooler, it does get
hot and photographs may be adversely affected by the heat and light.
2.
Never project old photographs as they are particularly sensitive to heat
and light and they will be damaged. Again, have a copy made.
3.
To prevent photographs from curling, mount them to a stiff backing
material or put them in a picture mat.
4. When projecting, make sure that the fan is operating and that the
c
ooling vents have not been obstructed.
W
hen finished tracing the
projected photo, turn the projector off and remove photo.
(OVER PLEASE)
Thank You…
for purchasing our Artograph Prism! The
Prism
™
projector has become the standard for
the discriminating artist, crafter and designer.
It offers increased performance and special
features to make scaling artwork and designs
faster and easier than ever before. You will find
your Prism projector ideal for projecting all
varieties of high contrast line art, photos,
patterns, and designs for an almost endless
range of applications. We hope you enjoy your
new Prism! If you have any questions
or suggestions, please contact us toll free at
888-975-9555.
SETUP & OPERATION
1
Step
1
2
4
5
6
WARRANTY
Be sure to fill out and mail the enclosed warranty registration card. You may
also register your Prism online at
www
.ar
tograph.com
.
Artograph projectors are guaranteed against all defects in material and
workmanship for five years from the date of sale to the original purchaser. Any
part of the equipment which becomes defective under normal installation and
use will be repaired or replaced without charge for factory labor and materials,
providing the equipment is returned, shipping pre-paid, to our factory within this
period. CONTACT OUR OFFICE FOR RETURN AUTHORIZATION. This warranty
does not apply to equipment which has been subjected to abuse, accident, or
alteration, nor to equipment which has been improperly installed or wired in
violation of the printed instructions furnished. The warranty registration card
should be filled out and returned immediately to ensure warranty service. You
may also register your Artograph product online at www.artograph.com.
PARTS LIST:
1. Prism Lens ....................200-728
2.
Retaining O-ring ...........151-571
(Prism Lens only)
3.
Power Switch
................145-306
4. Power Cord ...................145-347
5. Mirror ............................108-023
6. Lamps, Two 250-watt ...106-043
{
{
7.
Lid/Cover
......................151-523
8. Copy Clip ......................151-570
9. Top Glass .....................108-045
10. Right Lid Pivot ...............151-565
11. Left Lid Pivot .................151-564
2838 Vicksburg Lane North, Plymouth, MN 55447 USA
Tel: 888-975-9555 E-mail: [email protected]
www
.artograph.com
306-141
R
eduction
Position
8
0% - 160%
E
nlargement
Position
2
25% - 2000%
PRISM LENS
3
PROJECTOR
PRISM LENS
Produktspezifikationen
| Marke: | Artograph |
| Kategorie: | videopprojektor |
| Modell: | Prism |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Artograph Prism benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung videopprojektor Artograph
18 September 2025
18 September 2025
Bedienungsanleitung videopprojektor
- JMGO
- RCF
- Aiptek
- AAXA Technologies
- Marantz
- Ibiza Sound
- Ricoh
- Miroir
- Hisense
- Kindermann
- Edenwood
- Sony
- Xiaomi
- Vivitek
- Tracer
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
17 Januar 2026
16 Januar 2026
16 Januar 2026
14 Januar 2026
12 Januar 2026
11 Januar 2026
7 Januar 2026
7 Januar 2026
7 Januar 2026