Audio-Technica AT8010 Bedienungsanleitung

Lies die bedienungsanleitung für Audio-Technica AT8010 (2 Seiten) kostenlos online; sie gehört zur Kategorie Mikrofon. Dieses Handbuch wurde von 24 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 5 Bewertungen. Hast du eine Frage zu Audio-Technica AT8010 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

OMIDIRECTIONAL CONDENSER MICROPHONE

- All-purpose condenser microphone ideal for handheld interviews

and general audio acquisition

- Omni pattern provides maximum ambient pickup

- Switchable 80 Hz high-pass lter minimizes pickup of undesired

low-frequency sounds

- Operates on battery or phantom power

The AT8010 requires 11V to 52V DC phantom power or a 1.5V

AA battery for operation. A battery need not be in place for

phantom power operation.

Battery installation: Unscrew the lower section of the microphone

body, just below the nameplate. Insert a fresh 1.5V AA battery

in the handle compartment (“+” end up), then reassemble the

microphone. Alkaline batteries are recommended for longest life.

Remove the battery during long-term storage.

Output from the microphone’s XLRM-type connector is low

impedance (Lo-Z) balanced. The signal appears across Pins

2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” –

positive acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must

be wired consistently: Pin 1-to-Pin 1, etc.

An integral 80 Hz high-pass lter provides easy switching from a

at frequency response to a low-end roll-off. The roll-off position

reduces the pickup of low-frequency ambient noise (such as

traffic, air-handling systems, etc.), room reverberation and

mechanically coupled vibrations.

The high sensitivity of the AT8010 assures useful output and

an excellent match to most input sources. In some cases,

however, an attenuator such as the Audio-Technica AT8202 may

be required between the microphone and preamplifier to avoid

overloading sensitive input stages.

The microphone is RoHS compliant–free from all substances

specied in the EU directive on hazardous substances.

Avoid leaving the microphone in the open sun or in areas where

temperatures exceed 43°C for extended periods. Extremely high

humidity should also be avoided.

FORM No. ATGC-L0117-07-E

10 dB

20k10k5k2k1k50020010050

8 kHz

200 Hz

1 kHz

5 kHz

0°

330°

300°

270°

240°

210°

180°

150°

120°

90°

60°

30°

Polar Pattern

Frequency Response

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

Frequency in Hertz

LEGEND 12” or more on axis

Response in dB

same as 1 kHz

Machida • Tokyo • Japan

SPECIFICATIONS

ELEMENT Fixed-charge back plate

permanently polarized condenser

POLAR PATTERNOmnidirectional

FREQUENCY RESPONSE20-20,000 Hz

LOW FREQUENCY ROLL-OFF80 Hz, 12 dB/octave

OPEN CIRCUIT SENSITIVITY

(Phantom / Battery)

-44 dB (6.3 mV) re 1V at 1 Pa

-45 dB (5.6 mV) re 1V at 1 Pa

IMPEDANCE (Phantom / Battery)250 ohms / 300 ohms

MAXIMUM INPUT SOUND LEVEL

(Phantom / Battery)

137 dB / 123 dB SPL,

1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical)

(Phantom / Battery)

113 dB / 99 dB,

1 kHz at Max SPL

SIGNAL-TO-NOISE RATIO70 dB, 1 kHz at 1 Pa

PHANTOM POWER REQUIRMENTS11 - 52V DC, 2 mA typical

BATTERY TYPE1.5V AA/UM3

BATTERY CURRENT / LIFE0.4 mA / 1200 hrs typical (alkaline)

SWITCHES Flat, roll-off

WEIGHT (less cable and accessories)165 g

DIMENSIONS 178.0 mm long,

26.0 mm head diameter

OUTPUT CONNECTORIntegral 3-pin XLRM-type

ACCESSORIES FURNISHEDAT8405a stand clamp for ⅝"-27

threaded stands;

AT8136 foam windscreen;

⅝"-27 to ⅜"-16 threaded adapter;

battery;

soft protective pouch

Roll-off

Produktspezifikationen