Axxess TYTO-01 Bedienungsanleitung
Axxess
Nicht kategorisiert
TYTO-01
Lies die bedienungsanleitung für Axxess TYTO-01 (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 2 Bewertungen. Hast du eine Frage zu Axxess TYTO-01 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
TYTO-01
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 11/28/18 INSTTYTO-01
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
INTERFACE FEATURES
INTERFACE COMPONENTS
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Tape • Wire cutter • Zip ties
• Small flat-blade screwdriver
TABLE OF CONTENTS
Connections .........................................................2-3
Installation .............................................................3
Programming .........................................................3
Audio level adjustment .........................................3
Wiring diagram ......................................................4
Toyota Digital Amplifier Interface 2001-2015
• Designed for amplified models
• Retains balance and fade
• Micro-B USB updatable
• TYTO-01 harness
• TYTO-01 interface
• 16-pin harness with stripped leads
APPLICATIONS
See inside front cover
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date
vehicle specific applications
2
APPLICATIONS CONNECTIONS
LEXUS
ES Series 2007-2012
ES Series (w/ multi disc) 2002-2006
GS Series 2001-2005
IS Series 2002-2005
LS Series 2001-2006
RX Series 2004-2008
SC Series 2002-2010
TOYOTA
4-Runner 2003-2013
Avalon 2005-2010
Avalon 2011-2012
(Camry) Solara 2004-2008
Camry (w/o nav) 2012-2013
Camry 2007-2011
Corolla 2003-2011
TOYOTA (Cont.)
FJ Cruiser 2011-2014
Highlander 2008-2013
Matrix 2005-2012
Prius 3rd Gen (w/o nav) 2012-2015
Plug-In (PHV) (w/o nav) 2012-2015
Prius 2004-2011
Rav-4 2004-2014.5
Sequoia 2005-2012
Sequoia (w/o nav) 2013
Sienna 2004-2014
Tacoma 2005-2013
Tundra 2006-2013
Tundra (Double Cab) 2004-2005
Venza (w/ SD card based nav) 2013-2014
Venza 2009-2012
From the 16-pin harness with stripped leads to the aftermarket radio:
• Connect the wire to the left front positive speaker output.White
• Connect the wire to the left front negative speaker output.White/Black
• Connect the wire to the right front positive speaker output.Gray
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the wire to the radio’s left rear positive speaker output.Green
• Connect the wire to the radio’s left rear negative speaker output.Green/Black
• Connect the wire to the radio’s right rear positive speaker output.Purple
• Connect the wire to the radio’s right rear negative speaker output.Purple/Black
• Connect the wire to the amplifier turn on wire. This wire must be connected to Blue/White
hear sound from the factory amplifier.
• Tape off and disregard the following (6) wires, they will not be used in this application:
Red, , , , Brown Light Green Blue/Pink Green/Purple Orange/White,
Continued on the next page
3
REV. 11/28/2018 INSTTYTO-01
From the TYTO-01 harness to the aftermarket radio:
• Connect the wire to the ground wire.Black
• Connect the Yellow wire to the battery wire.
• Connect the wire to the accessory wire.Red
• Connect the wire to the power antenna wire.Blue
• If the aftermarket radio has an illumination wire, connect the Orange wire to it.
With the key in the off position:
1. Connect the
16-pin harness with stripped leads
, and the
TYTO-01 harness
into the interface.
2. Connect the
TYTO-01 harness
to the wiring harness in the vehicle.
1. With the vehicle and radio turned on, turn the volume up 3/4 of the way.
2. With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio
level; counter clockwise to lower the audio level.
3. Once at a desired level, audio adjustment is complete.
1. Turn the key (or push-to-start button) to the ignition position and wait until the radio
comes on. The factory amplifier should come on and you should hear sound at this point.
2. Test all functions of the installation for proper operation, before reassembling the dash.
Note: To use fade, ensure the radio is turned up 3/4 of the way.
CONNECTIONS (CONT.) PROGRAMMING
AUDIO LEVEL ADJUSTMENTINSTALLATION
Produktspezifikationen
| Marke: | Axxess |
| Kategorie: | Nicht kategorisiert |
| Modell: | TYTO-01 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Axxess TYTO-01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Axxess
23 Juni 2025
22 Juni 2025
12 September 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
30 August 2024
Bedienungsanleitung Nicht kategorisiert
- Brondell
- EnGenius
- Titanwolf
- Milesight
- Sure-Fi
- Aim TTi
- Gemini
- Trijicon
- Magic Care
- Navionics
- Meinl
- ZKTeco
- Flavour Blaster
- Diana
- SBS
Neueste Bedienungsanleitung für -Kategorien-
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025
23 Juni 2025