Barco ImagePRO-4K Bedienungsanleitung

Lies die bedienungsanleitung für Barco ImagePRO-4K (2 Seiten) kostenlos online; sie gehört zur Kategorie Router. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 13 Bewertungen. Hast du eine Frage zu Barco ImagePRO-4K oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Note: The ImagePRO4K automatically acquires and congures inputs.–

Setting up an LED display

Note: To enter the Setup menu press the Adjust Knob.

ImagePRO4K Video Processor: Rear-Panel Setup–

Genlock

BNC Input

Quick install and setup

ImagePRO4K Video Processor–

Quick Start Guide - Setup

P/N 26-1602004-00, Rev 01

Connect inputs Connect all input sources to the —

ImagePRO 4K.–

1Connect power Ensure that power is properly connected —

to the ImagePRO4K.–

2

Getting started

Barco Technical Support:

USA:

EMEA:

China:

APAC:

Support:

+1 (866) 374-7878

+32 (56) 36 8019

40088 22726

+603-78803362

www.barco.com/en/support

3

4

5

Connect outputs Connect the output(s) on the —

ImagePRO4K to your projector(s) or other target devices.–

Turn on power Turn on power to the ImagePRO4K, — –

your projector(s), and to all peripheral equipment.

Factory reset If you are using the ImagePRO4K for the — –

rst time, or if you are using an ImagePRO4K that has just –

returned from an event, perform a full factory reset to restore

default system congurations.

Press the Adjust Knob to enter the Setup menu, then select

Reset / FactoryReset / Soft Reset on the display screen.

keeps the user settings.

Adjust output formatSetup / Output / AUX Go to —

Adjustment and update the output format.

6Native Rate O—n the front panel, press the Adjust Knob to

enter the Setup menu, then select and Setup / System menu

select the desired Native Rate.

8

Setting up outputs

9

10

Test output Turn on a test pattern, verify that you have an —

image, and make any necessary adjustments. When

complete, turn o the test pattern.

11 Set and adjust inputs / source Select inputs / sources and make any —

necessary adjustments to color balance, timings, and so on.

Setting up inputs / source

12

Save input / source configurations After adjusting an input / source, —

save the input /source configuration.

Repeat steps 11 and 12 for each input / source.

13 Adjust and save system settings Adjust system parameters such as —

Ethernet settings and HDCP parameters.

For complete details on all installation and operations procedures, please

refer to the (R5906167).ImagePRO 4–K User’s Guide

ImagePRO 4–K User’s Guide

AC

Connect to AC

power source

Ethernet

Connect to Event

Master Toolset or

External Controller

Genlock

Generated

Reference Output

DP 1.2

Input

HDMI 2.0

Input

12G SDI

Input

12G SDI

Input

12G SDI

Input

12G SDI

Input

DP 1.2

Output

HDMI 2.0

Output

12G SDI

Output

12G SDI

Output

12G SDI

Output

12G SDI

Output

Position and adjust the image Use the LED Setup Menu to —

position the image on the LED wall or other display device,

scale the image, adjust and settings, and save your Pan Zoom

view.

Save AllSave AllSave All Select —. is the last menu item on the Setup

page. writes system settings to non-volatile memory.Save All

14

System settings

Assign primary output If the primary output is DP, —

proceed to the next step.

If your primary output is HDMI/SDI, go to Setup / Output /

AUX Adjustment and update the primary output.

7

Produktspezifikationen