Behringer Clocked Sequential Control Module 1027 Bedienungsanleitung

Lies die bedienungsanleitung für Behringer Clocked Sequential Control Module 1027 (3 Seiten) kostenlos online; sie gehört zur Kategorie Hamer. Dieses Handbuch wurde von 26 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 3 Bewertungen. Hast du eine Frage zu Behringer Clocked Sequential Control Module 1027 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

CLOCKED SEQUENTIAL

CONTROL MODULE 1027

Legendary 2500 Series 8-Position Step

Sequencer Module for Eurorack

Controls

(1) CH A / CH B / CH C SEQUENCER COLUMNS – Use the

knobs to set the control voltage output for each step.

Each column sends out control voltages via that channel’s

respective CH A / CH B / CH C output jack.

(2) STEP LEDs – Each LED lights to indicate its respective

sequencer step is active.

(3) POSITION GATES – Each of these output jacks sends out a

gate signal for its respective sequence step via cables with

3.5 mm TS connectors. These 8 gate output signals are

also available via the 12-pin GATE OUT LINK CONNECTOR

located on the module underside. This 12-pin connector

can connect to and trigger other compatible modules,

such as the MIX-SEQUENCER MODULE 1050, via a 12-pin

ribbon connector.

(4) RATE – This knob controls the step speed at which the

sequencer moves from step to step. The knob operates

in two overall frequency ranges determined by the

LOW/HIGH switch.

(5) LOW/HIGH – Use this sliding switch to set whether the

RATE knob operates in a lower-frequency (LOW) or

higher-frequency (HIGH) range.

(6) % PULSE WIDTH – Select between width settings

for the rectangular waveform ranging from 5% to 95%

duty cycle. The PULSE WIDTH control operates on the

CLK OUT jack only, making this control very useful for

triggering other modules such as envelope generators,

and so on.

(7) INT/EXT – Use this switch to select between internal (INT)

or external (EXT) pulse width control voltage. When EXT

is selected, the % PULSE WIDTH control knob is disabled.

(8) ON /OFF – This button starts or stops the sequence with a

manual button push.

(9) STEP – Press this button to manually progress to the next

sequencer step.

(10) RESET – Press this button to manually restart the

sequence at step 1.

(11) STEP – Use this jack to route external trigger signals for

the STEP button into the module via cables with 3.5 mm

TS connectors.

(12) RESET – Use this jack to route external trigger signals for

the RESET button into the module via cables with 3.5 mm

TS connectors.

(13) ON – Use this jack to route external trigger signals to

enable the step counter into the module via cables with

3.5 mm TS connectors.

(14) OFF – Use this jack to route external trigger signals to

disable the step counter into the module via cables with

3.5 mm TS connectors.

(15) RATE – Use this jack to route in external control voltage

signals for the sequencer's step speed (usually controlled

by the RATE knob) via cables with 3.5 mm TS connectors.

(16) WIDTH – This jack allows control voltage and modulation

signals for the rectangular waveform to be routed in via

cables with 3.5 mm TS connectors.

(17) CH A – This jack sends out control voltage signals for

the CH A sequencer column via cables with 3.5 mm

TS connectors.

(18) CH B – This jack sends out control voltage signals for

the CH B sequencer column via cables with 3.5 mm

TS connectors.

(19) CH C – This jack sends out control voltage signals for

the CH C sequencer column via cables with 3.5 mm

TS connectors.

(20) CLK OUT – Use this jack to export the internally generated

clock signal via cables with 3.5 mm TS connectors.

The internal clock produces a gate pulse every time

the sequencer steps, and the gate pulse’s width can be

adjusted using the % PULSE WIDTH control or via the

WIDTH control jack.

(1) (3)(2)

(4)

(5)

(6)

(7)

(8)

(9)

(13) (14)(15)(16)(17)(20)(18)(19)(12)

(10)

(11)

V 1.0

Quick Start Guide

Produktspezifikationen