Bixolon SRP-380II Bedienungsanleitung

Lies die bedienungsanleitung für Bixolon SRP-380II (4 Seiten) kostenlos online; sie gehört zur Kategorie Drucker. Dieses Handbuch wurde von 20 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 10.5 Bewertungen. Hast du eine Frage zu Bixolon SRP-380II oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

◈Information

This installation guide contains quick information required for the product

installation. Please refer to the Software and Documents provided on the

Download section of the BIXOLON Website (www.bixolon.com) for more

information on how to setup.

1. Manual: User’s Manual, Code Table, Control Commands, etc.

2. Driver: Windows, OPOS, CUPS (Linux, Mac), VCOM (USB, Ethernet)

3. SDK: UPOS SDK (Windows, Android, iOS)

4. Utility: Unified POS Utility, Net Configuration Tool, Android Utility, iOS Utility

We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions

and quality of all our products. In following, product specifications and/or user

manual content may be changed without prior notice.

Please refer to the BIXOLON website for the addresses and phone numbers of

the company's headquarters and branch offices.

◈Components

SRP-380plus/382plus

DK Gender

Cable Cover

USB A-B Cable

Installation Guide

AC/DC Adaptor

Power Cord

Paper Roll

◈Cable Connection

1. Turn off the printer and peripheral devices.

2. Connect the power cord to the adapter and connect the adapter to the power

supply connector of the printer.

3. Check the type of the interfaces at the back of the printer (USB, Serial,

Parallel, Ethernet, Powered USB, Wireless LAN, Bluetooth) and connect the

interface cable.

4. Connect the drawer kick-out cable to the drawer kick-out port located on the

underside of the printer.

- Be sure to turn off the printer and connect or disconnect

the adapter jack.

-Only use a power supply provided by Bixolon

- Pay attention to the direction in which you insert the

adapter jack.

◈Installing Paper Roll

1. Push the Cover Open Button to open the

Printer Cover.

2. Insert new roll paper in the correct

direction.

3. Pull the paper out slightly and close the

Printer Cover.

When closing the cover, press down on the center of the cover

to ensure that the paper is in contact with the roller. Printing

quality may not be optimum if the recommended paper is not

used.

◈Using Control Panel

• Power (LED)

The Power LED is on whenever the printer is on.

• Error (LED)

Red light will be on in various error conditions such as out of

paper, cover open, etc.

• Paper (LED)

Red LED will be lit when the paper roll is running low.

The LED keeps blinking when the printer is in self-test standby

mode or macro execution standby mode.

• Feed (Button)

Press this button to feed the paper out.

Hold down this button to feed out the paper continuously.

◈Self-Test

You can check whether printer works correctly or not through the self-test.

Printing quality, ROM version, and memory switch settings can be checked

through the self-test function.

1. Check whether paper is mounted correctly.

2. Turn on the power while holding down the Feed button and the self-test

procedure will begin.

3. The printer will print out the current status of printer including the version of

ROM.

4. After printing out the current status of printer, the printer will print following

lines and waits for the next step (paper lamp will keep blinking).

Self-TEST PRINT COMPLETE

SELECT MODE BY PRESSING THE FEED BUTTON.

End of SELF-TEST : Less than 1 second

VMSM Selection : 1 second or more

5. Press the Feed button to resume printing or hold down the button for at

least one second to change the VMSM settings.

5-1 If “Continuous SELF-TEST” is selected

(1) Press the Feed button for less than one second to print the preset page.

(2) The self-test ends automatically as it prints the following line and cuts

the paper.

*** COMPLETED ***

(3) The printer goes into normal print mode upon completion of the self

test.

5-2 If “VMSM Selection” is selected

(1) The following lines will be printed when the VMSM opens.

** VMSM Selection **

0 : Exit and reboot printer

1 : Print current settings

2 : Set Print Density

3 : Set Print Speed

4 : Set Cutting mode

5 : Set Buzzer

6 : Set Near-End Sensor

7 : Set Serial Interface

(2) Press the Feed button to run the above function.

▶Step 1(Select Options): press the button a number of times as shown

by each menu.

▶ Step 2(Enter Options): hold down the button for at least one second

to apply each item selected.

If you select any items not listed above, the list of “VMSM

Selection” will be printed again. Setting the mode will be canceled

if no item is selected in Step 1.

If “0: Exit and reboot printer” is not executed, the new settings will

not be saved.

(3) Hold down the Feed button for at least 1 second to save the changes.

The following line will be printed before cutting the paper.

*** COMPLETED ***

6. The new settings will be automatically applied when printer resets.

Printer Installation Guide & Safety Guide

KN04-00237A (V1.01)

THERMAL RECEIPT PRINTERSRP-380/382plus

Power Jack

Ethernet

Cable

Interface Cable

(Serial/Parallel/Powered USB/

Wireless LAN/Bluetooth)

AC/DC Adapter

Adapter Jack

Interface port

USB

Cable

Ethernet Port

USB Port

Power Port

Drawer

Kick-out

Port

Drawer

Kick-out

Cable

Produktspezifikationen