BlendMount BMX-2121 Bedienungsanleitung
BlendMount
Nicht kategorisiert
BMX-2121
Lies die bedienungsanleitung für BlendMount BMX-2121 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 13 Bewertungen. Hast du eine Frage zu BlendMount BMX-2121 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
PART# BMX-2121
Hien
ESCORT
PASSPORT
MAX
1
i1111111
1
111
111
1
11
111
11
1
11
11
Innovative
Mount
i
ng
Solut
i
ons
LEFT HAND DRIVE VEHICLE
1
28028
43650
l
INSTALLATION INSTRUCTIONS FOR THE ESCORT PASSPORT MAX RADAR DETECTOR
Your rear
view
mirror
has
minimal
clearance between
the
back
side
of
the
mirror
and the
mirror
stem.
It
is
very
important
that
this
mount
is installed
correctly
to
ensure
mirror
adjustability
is retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE:
For
illustration
purposes,
the
mount
and rear
view
mirror
shown
in these
instructions
may
look
slightly
different
then YOUR
mount
and rear
view
mirror.
OPPOSING FORCES
1 - The RELEASE Button on the radar detector (RD) is
NOT
used with this mount.
To
release the tension
of
the spri
ng
clip, simply squeeze the TRIGGER and the back side
of the mount together. This
will
lower the bottom porti
on
of the spring clip allowing you to
slide the
RD
on
and off. When used properly, the spring clip avoids putting excessive
pressure
on
the mirror stem when installing and removing the
RD
. The
top
portion
of
the mount should barely
move
when the
two
opposing forces are applied.
TOP
SECTION
---~
-,r~
-.
TOP AND MID
SECTIONS MUST TOUCH
AT THE PIVOT POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
3 - Loosen the clamp screw so the top section separates from the mid section. This will
provide the necessary clearance to slide the mount over the mirror stem as shown above.
Ad
just the mirror parallel to the windshield for ease of installation. As you are tightening the
clamp screw, make sure the top and mid sections touch at the pivot point.
If
they
do
not
touch
at
the pivot point, this
mount
is
incompatible with your mirror type. Tighten the
clamp screw until the mount is
sl
ightly snug around the mirror stem.
BOTTOM
OF
SPRING CLIP
IS PARALLEL WITH
RO
2 - The
bottom
of
the
spring
clip
must
be parallel
with
the
top
of
the
RD
to
slide
in and out. SLIDE THE RD ONTO
THE SPRING CLIP AS FAR AS IT WILL GO. Release the
tr
igger to secure the
RD
onto the mount. Before installing the
mount onto your rear view mirror, remove and
in
stall the RD a
few times
so
you can observe how the spring clip functions.
4 - Position the mount as far forward as you
can
. Befo
re
fully tightening the clamp screw,
make sure the bottom of the mount
is
parallel
with the bottom of the mirror.
Innovative Design
And
Precision Manufacturing
BlendMount -
US
PATENT#
0625
,580 S, 0656,
811
S, D653,980 S
0690,245 S, 0690,246 S, 0690,247 S and other patents pending
PAGE 1 OF 2
Produktspezifikationen
| Marke: | BlendMount |
| Kategorie: | Nicht kategorisiert |
| Modell: | BMX-2121 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit BlendMount BMX-2121 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert BlendMount
13 September 2025
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
Bedienungsanleitung Nicht kategorisiert
- Charge Amps
- Dyson
- Küppersbusch
- Digi
- Xvive
- Vent-A-Hood
- Pioneer
- Compex
- OVIDE
- Garden Feelings
- AVerMedia
- LAS
- Vox
- NordicTrack
- Fluidmaster
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026