C Pure Oceanloch+ L2 Bedienungsanleitung
C Pure
Wasserfilter
Oceanloch+ L2
Lies die bedienungsanleitung für C Pure Oceanloch+ L2 (1 Seiten) kostenlos online; sie gehört zur Kategorie Wasserfilter. Dieses Handbuch wurde von 6 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 3.5 Bewertungen. Hast du eine Frage zu C Pure Oceanloch+ L2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
INCLUDED IN PACKAGE
4 x 7.5" Self-Seal Bubble Wrap Bag
3/8" Sch 80 Tee with 3/8" x 1/4"
Reducer Bushing
3/8" Double O-Ring Short Nipple
3/8" Threaded PVC Ball Valve
2" 0-100psi Steel Gauge
2 @ #10 x 1" SS Screws
Instruction Sheet
This system is designed to treat cold water only. The installation must be on a cold
water supply.
Do not use to treat water that is microbially unsafe or of unknown quality without adequate
disinfection before and after the system.
The system must be installed in accordance with all applicable state and local laws
and regulations.
Filter cartridge must be replaced every 3-6 months,
or at the rated capacity, or if a noticeable reduction in
flow rate occurs.
INSTALLATION INSTRUCTIONS
1. Shut off power to equipment if necessary.
2. Turn off water supply to system.
3. Remove the cartridges from the system following the instructions.
4. Place and install the filter system using the two #10 x 1 stainless screws "
provided for wall mounting. Allow at least 3 of space below the cartridge for "
easy removal and replacement.
5. Install inlet ball valve and outlet pressure gauge (as shown).
5a. If you’re installing a system with an inlet pressure gauge, attach the inlet
gauge to the inlet side of the system. Then, install inlet ball valve to the inlet
pressure gauge.
6. Connect inlet and outlet ports using appropriate NSF-approved components.
Do not connect the outlet port to equipment until after flushing (Step 10).
7. Lubricate O-rings on cartridges with a food grade silicone lubricant prior to
installation.
8. Line up locking features as shown and push cartridge up into head until it stops.
Use free hand to support at top of bracket. Turn cartridge 1/4 turn to the right
until it stops to lock in place.
9. Connect a piece of tubing to the outlet port and run it to a drain or bucket.
10. Turn on water to the system. Allow water to run to drain for 5 minutes to purge
air and rinse out carbon fines.
11. Turn off water. Connect system to equipment.
12. Turn on water. Check for leaks and repair as needed.
13. Restore power to equipment. The system is ready for operation.
ININ
ALIGNMENT POINTS
INLET
OUTLET
CARTRIDGE REPLACEMENT
TO REMOVE OLD CARTRIDGE
Twist to the left to unlock
TO INSTALL NEW CARTRIDGE
Align with guide point
Push straight up
Pull straight down
Twist to the right to lock
04/2025
#790OCLOKITL2,
#790OCLOKTL2G
System Model
Flow Rate
(GPM) (LPM)
790OCLOKITL2 3.33 12.64
Capacity
Replacement Part
Number
(G) (L)
36,000 136,260 790OCLOCRTL2
Max Operating
Temp.
Max Operating
Pressure
100°F (38°C)
125 PSI
(8.62 bar)
OCEANLOCH+ L-2 REV 1 4-20
INSTALL ATION MANUAL
L
+
Produktspezifikationen
| Marke: | C Pure |
| Kategorie: | Wasserfilter |
| Modell: | Oceanloch+ L2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit C Pure Oceanloch+ L2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Wasserfilter C Pure
11 Juni 2025
Bedienungsanleitung Wasserfilter
- Hydor
- Aqua Medic
- Solac
- Katadyn
- T.I.P.
- Everpure
- BWT
- LifeStraw
- Imetec
- Avanti
- Pureit
- EcoWater
- LG
- Oliveri
- Sunbeam
Neueste Bedienungsanleitung für -Kategorien-
13 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
8 Juni 2025
8 Juni 2025