Canarm PW-14S Bedienungsanleitung
Canarm
Nicht kategorisiert
PW-14S
Lies die bedienungsanleitung für Canarm PW-14S (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Canarm PW-14S oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
Page 1 of 4
M-PW 26_03_25
GENERAL SAFETY
DIMENSIONS & COMPONENTS
The purpose of this manual is to aid in the proper installation and operation of the Canarm PW Series direct drive radial blade pressure
blowers. These instructions are intended to supplement good general practices and are not intended to overwrite local codes and
ordinances.
IT IS THE RESPONSIBILITY OF THE PURCHASER TO ENSURE THAT THE INSTALLATION AND MAINTENANCE OF THIS
EQUIPMENT IS HANDLED BY QUALIFIED PERSONNEL.
Inspect all shipments carefully for damage. THE RECEIVER MUST NOTE ANY DAMAGE ON THE CARRIER’S BILL OF LADING AND
FILE A CLAIM IMMEDIATELY WITH THE FREIGHT COMPANY.
The PW series come prepared from the factory, ready to run when installed and wired. 1.
All electrical work must be done in accordance with all applicable electrical codes by a 2.
qualified electrician.
Prior to wiring the unit, ensure the power supply is locked out in the OFF position and that 3.
the voltage matches the motor’s requirement, located on the motor’s name plate.
Caution: The unit contains rotating parts, & electrical service. Use appropriate caution when 4.
installing and servicing the unit. Install guarding around the intake venturi, or outlet discharge
in applications where it will be not be ducted.
Before starting the unit, ensure all parts are secure & the wheel rotates freely. 5.
Check and tighten where necessary all screws, nuts, bolts, etc. prior to starting the unit. 6.
Some may have loosened during shipping.
NOTE: Check and tighten all hardware after 2 days of initial operation. 7.
Make sure there is no foreign debris in the fan compartment or lodged in the wheel itself. 8.
Blowers should be installed on solid structural foundations. Vibration isolators are 9.
recommended. Work should be done under the supervision of licensed mechanical
contractors.
Always wear appropriate safety equipment when installing or 10.
servicing the unit.
Please follow all applicable national, state/provincial and local 11.
codes. All of them will supersede this manual.
Failure to follow the safety instructions in this manual may 12.
cause serious injury or death due to electrical shock or high
speed rotating parts.
!"#$
!"#$%&'&(")$%)$())*##+!)$(+"#$*%"!$*+"!$*+"!$*),%,"+$**")$()#")$*)(""""
!"#%
-&'&("#$% )$( )(")$* * #")$( #")$( +"+$* ! )$( ,"#$* +"#$% ,"!$* ,"#$% (."#$% + !")$( -"#$* )%"+$* ), """"
!"#&&
)."+$*&'&# +$* )%"#$% - % #")$( ,"!$* !")$* #$% !")$% ,")$( * !"+$* (."#$% , *"+$* ))"#$% )*")$% ), """"
!"#&'
)(")$(&'&#!$*)!*+%*,")$(#$%*")$%!")$(--"+$*(.")$*!).)."+$*)*"#$*)+""""
!"#&(
)#")$(&'&%"#$* &)")$* )!"+$* ))")$% !")$* +"#$% * -"-$), ) ).")$( -"+$* ))"#$* )) (( * ))")$( )("+$* ()")$( )+ !")$%
/0123456789 :;<=
)*+,-.
/*0
"1,,- 2*3, >?@
PW SERIES
DIRECT DRIVE RADIAL
BLADE PRESSURE BLOWERS
OPERATION INSTRUCTIONS AND PARTS MANUAL
PLEASE READ AND SAVE THESE INSTRUCTIONS
Produktspezifikationen
| Marke: | Canarm |
| Kategorie: | Nicht kategorisiert |
| Modell: | PW-14S |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Canarm PW-14S benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Canarm
19 Januar 2026
18 Januar 2026
17 Januar 2026
13 Januar 2026
13 Januar 2026
12 Januar 2026
12 Januar 2026
11 Januar 2026
11 Januar 2026
11 Januar 2026
Bedienungsanleitung Nicht kategorisiert
- Paladin
- Dataflex
- Ring
- Aqara
- Epson
- Craftsman
- Merging
- Goal Zero
- AstralPool
- O&O Software
- DishTV
- Klein Tools
- Kopul
- Nostalgia
- Dremel
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026