Casio GW-A1100-1A3ER Bedienungsanleitung

Lies die bedienungsanleitung für Casio GW-A1100-1A3ER (11 Seiten) kostenlos online; sie gehört zur Kategorie betrachten. Dieses Handbuch wurde von 70 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 35.5 Bewertungen. Hast du eine Frage zu Casio GW-A1100-1A3ER oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Operation Guide 5311

E-9

2. Check the Home City.

Use the procedure under “To confi gure Home City settings” (page E-36) to confi gure your

Home City.

Important!

xProper time calibration signal reception depends on correct Home City, time, and

day settings in the Timekeeping Mode. Make sure you confi gure these settings

correctly.

3. Set the current time.

xTo set the time using a time calibration signal

See “To get ready for a receive operation” (page E-25).

xTo set the time manually

See “Confi guring Current Time and Day Settings Manually” (page E-41).

The watch is now ready for use.

xFor details about the watch’s radio controlled timekeeping feature, see “Radio

Controlled Atomic Timekeeping” (page E-20).

E-8

Things to check before using the watch

1. Hold down at least two seconds to enter the Timekeeping Mode, and C

then observe the movement of the

x

x

x

xx

.Second Hand

Is the

x

x

x

xx

moving smoothly at one-second intervals?Second Hand

Is the

x

x

x

xx

moving at Second Hand

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged. For details

about charging, see “Charging the

Watch” (page E-14).

Power is low. Charge the watch by

placing it in a location where it is

exposed to light. For details, see

“Charging the Watch” (page E-14).

NO

YES

YES

NEXT

E-7

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the

current high-speed movement or press any button.

Note

xIf you do not perform any operation for more than two minutes after pulling out the

crown, crown operations will become disabled automatically. If this happens, push

the crown back in and then pull it out again to re-enable crown operations.

xYou can use high-speed hand movement when confi guring time settings in the

Timekeeping Mode, Alarm Mode, or Countdown Timer Mode.

xButton operations become disabled after you perform a crown operation. If this

happens, rotate the crown slightly. This should restore button operations.

E-6

High-speed Movement

When rotating the crown to move the hands of the watch, you can use the operations

described below to move the hands at high speed, either forward or back. There are

two high-speed levels: HS1 and HS2 (faster than HS1).

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly three turns away

from you (for forward movement) or towards you (for reverse

movement). High-speed movement will continue even if you

release the crown.

To start HS2 high-speed movement

While HS1 high-speed movement is in progress, again rotate

the crown rapidly three turns in the same direction as the

current HS1 movement (away from you for forward movement

or towards you for reverse movement).

E-5

4. Gently pull on the crown to make sure it is securely locked and does not come out.

To unlock the crown

Rotate the crown so the groove aligns with Mark 1.

To pull out, rotate, or push the crown in

Important!

xBefore performing any of these operations, fi rst unlock the crown.

The illustrations below show the different crown operations.

Pull outRotatePush in

E-4

Using the Crown

This watch has a lock-type crown.

Important!

xYou should normally have the crown locked during normal daily use. Leaving the crown

unlocked creates the risk of unintended operations or even damage due to impact.

To lock the crown

1. Push the crown back in (see “To pull out, rotate, or push the

crown in” below).

xNote that attempting to lock the crown when it is not pushed

in can cause unexpected watch operation.

2. Rotate the crown so any one of its three grooves is aligned

with Mark 1.

3. While pushing in on the crown (a), rotate it to the right (b) until

it stops, and align the groove with Mark 2.

Mark 1

Groove

W

V

Mark 2

E-3

About This Manual

Operations are performed using the watch’s crown, and

the three buttons indicated by the letters , and in A BC

this manual.

Hands and Indicators

z

z

z

z z

Hour Hand

x

x

x

x x

Second Hand

c

c

c

c c

Minute Hand

v

v

v

v v

Upper Dial Hand: Indicates a time, in 24-hour format,

depending on the current mode.

b

b

b

b b

Lower Dial Hand: Indicates the current mode.

n

n

n

n n

Day Indicator

This User’s Guide uses numbers shown above to identify

watch hands and indicator.



>

>

>

>>

B

B

B

BB @

@

@

@@

6

6

6

66

*

*

*

**

+

+

+

++

E-2

Warning!

xThe measurement functions built into this watch are not intended for taking

measurements that require professional or industrial precision. Values produced

by this watch should be considered as reasonable representations only.

xTo ensure correct direction readings by this watch, be sure to perform

bidirectional calibration before using it. The watch may produce incorrect

direction readings if you do not perform bidirectional calibration. For more

information, see “To perform bidirectional calibration” (page E-56).

xNote that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

xNote that the product illustrations in this manual are intended for reference only, and

so the actual product may appear somewhat different than depicted by an illustration.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours. Because of this, the radio-controlled atomic timekeeping function will not

display the correct time for Newfoundland, Canada.

MA1303-EA

Ú

#!3)/#/-054%2#/,4$

Produktspezifikationen