CDA KC23WH Bedienungsanleitung

CDA Spülbecken KC23WH

Lies die bedienungsanleitung für CDA KC23WH (4 Seiten) kostenlos online; sie gehört zur Kategorie Spülbecken. Dieses Handbuch wurde von 87 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 44 Bewertungen. Hast du eine Frage zu CDA KC23WH oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/4

www.cda.eu

Ceramic Sinks

Installation

Before Installation

Oer up the sink to the worktop and/or the cabinets to conﬁrm that

the external dimensions of the bowl are compatible with the cabinets

themselves.

Conﬁrm that with the sink in position:

• There is adequate space to install any taps or other required

accessories.

• There is adequate space to install the waste pipework and that any

necessary modiﬁcation to internal shelves to accommodate the waste

(and trap) is acceptable.

• Access to any water stop-cock or other services will still be adequate

after the installation.

Cutting the tap hole

Only cut/punch the tap hole from the top face of the sink.

• Select the tap hole position based on whether left hand or right hand

drainer is required.

• Locate the centre of the required tap hole by transferring

measurements from the cast in features on the underside. Cover the

top of the tap hole cut-out area with masking tape.

• Caution: Ensure that the sink is supported under the hole to be cut

out.

• Using a centre punch and hammer, make an initial cut in the glaze at

the centre of the required hole.

• Still using the punch and hammer enlarge the cut to the full hole size

required for the tap by carefully chipping away.

E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the

right to change speciﬁcations without prior notice.

Installation

• Refer to the cut-out sizes on the back of this manual and use them

to mark out where the worktop needs to be cut. Double-check the

dimensions before cutting the worktop aperture.

• After cutting out the worktop aperture, we recommend you seal the

cut edges with silicone (or similar) sealant to help prevent ingress of

water.

• It is often easier to mount the taps, waste-ﬁtting and overﬂow onto the

sink prior to ﬁtting the sink to the worktop.

• Position the sink on the worktop, bedding it into a bed of silicone

sealant.

• After positioning the sink, leave it untouched for 24 hours to allow

the sealant to cure before any water is run into it.

• The taps, waste-ﬁtting and overﬂow can now be mounted onto the

sink (if not already done) and fully connected to their respective

services.

• To check the waste for leaks, close the plug/basket of the waste

ﬁtting, open the tap and ﬁll the sink to the level of the overﬂow; turn

o the tap and wait several minutes to verify that the water doesn’t

drain away.

• Empty the sink.

After ﬁtting, ensure that the enclosed “Ceramic Sinks Use and

Maintenance” guide is retained for the customer and/or user of the

sink.

Produktspezifikationen

Marke:	CDA
Kategorie:	Spülbecken
Modell:	KC23WH
Breite:	1010 mm
Tiefe:	510 mm
Produktfarbe:	Weiß
Höhe:	225 mm
Erste Schale Größe:	200 mm
Anzahl der Spülbecken:	1 Becken
Erste Schale Dimensionen (WxL):	460 x 405 mm
Waschbeckenmaterial:	Keramik
Abtropfbrett:	Ja
Position des Abtropfbretts:	Doppelseitig
Wasch-/Spülbeckentyp:	Aufsatzwanne
Form des Beckens:	Rechteckig
Form erste Schüssel:	Rechteckig
Abfluss:	Nein
Wasserhahn enthalten:	Nein