Cocraft DL-04 Bedienungsanleitung

Lies die bedienungsanleitung für Cocraft DL-04 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 43 Personen als hilfreich bewertet und erhielt im Schnitt 3.6 Sterne aus 22 Bewertungen. Hast du eine Frage zu Cocraft DL-04 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

GREAT BRITAIN

For consumer contact, please visit www.clasohlson.co.uk

and click on customer service.

Digital Spirit Level

Art. No 40-8180 Model DL-04 (D600XP)

Please read theentire instruction manual before use and save it for future

reference. Wereserve theright for any errors in text or images and for making any

necessary technical changes to this document. Ifyou should have any questions

concerning technical problems please contact our Customer Services.

Safety

• Always keep thespirit level out of thereach of children and animals.

• Remove exhausted batteries.

• Do not incinerate exhausted batteries.

• Do not short-circuit thebatteries.

• Do not mix old and new batteries.

• Make sure that thebatteries are inserted as indicated by themarkings in

thebattery compartment.

Care and maintenance

The spirit level is aprecision instrument and must be handled with care.

Do not expose thespirit level to dust and moisture. The spirit level must not

be subjected to blows, vibration and extreme temperatures. If thespirit level

is to be unused for along time, remove thebatteries.

Disposal

Follow local ordinances when disposing of this product. If you are unsure

about how to dispose of this product contact local council.

Description

• 600 mm digital spirit level.

• Sturdy aluminium frame.

• Two bubble vials for level and plumb, high precision, deviation only ± 0.5 mm/m.

• Digital slope measurement, accuracy ± 0.2°. Resultcan be displayed in °,

%, mm/m or in/ft.

• V-shaped groove along theentire underside allows precision measurement

on pipes as well.

If you choose theunits in/ft, thedisplay

shows H = 6 7/8” (H=L·tan α, L = 3.28 ft,

α = 30°). If you choose slope in %,

thedisplay shows H = 57.72 (H=L·tan , α

L = 100, α= 30°).

Buttons

1. [CAL] Press to enter calibration mode.

2. [UNIT] ] Press to toggle between different display units: ° (degrees),

% (slope), mm/m and in/ft (rising - falling).

3. [Hold] Press to save thecurrently displayed data. Whenthe hold function

has been activated, thedisplay shows H”. Press[Hold] again to deac-“

tivate thefunction.

4. [REF] Press to save areference point. Whenthe reference point has been

saved, thedisplay shows S”. Press[REF] again to deactivate it.“

5. [Audio] Switch buzzer on/off. Whenthe buzzer is on, it sounds at 0°, 45°

and 90° (± 0.5°).

6. [] Press to switch on thespirit level. Holddown for about three seconds

to switch off thespirit level.

Display icons

7. Showsgraphically whether thelevel is sloping up or down or is level.

8. Showsthat thebuzzer is active

9. Hshows that thehold function has been activated (display data frozen)

10. Sshows that areference point has been saved

11. Showsthe slope

12. Batterystatus

Examples of different displays for thesame slope. Press[UNIT] to change

thedisplay units.

Measuredslope is

displayed in

degrees: 30°

Measuredslope

is displayed as

apercentage:

57,72 %

Measuredslope is

displayed in

millimetres/metre:

577 mm/m

Measuredslope

is displayed in

inches per foot:

6 7/8 in/ft

Ifthe angle is greater than 45° but less

than 90° (H=L/tan ).α

NOTE: The display switches off automatically when thebatteries are low.

Tosave thebatteries there is an automatic switch-off function which switches

off thespirit level if it has been motionless for three minutes.

Use

1. Press []; thedisplay comes on.

2. Placethe spirit level on alevel surface. Theslope is displayed directly as 0–90°.

3. Theangle is displayed in both directions.

Measurement from a reference surface

During measurement you can save ameasured

value as 0° so that it can be used as areference

for thenext measurement.

Example: You want to use theslope (A) as

areference for thenext measurement (B).

1. Place thespirit level on thereference surface (A).

2. Press [REF]. Thedisplay shows 0”.“

3. Place thespirit level on thenew measurement

surface (B).

4. Read off theangle between (A) and (B) on

thedisplay.

Calibrating the spirit level

1. Placethe spirit level on aat surface with aslope of less than 5°.

Ifthe slope is greater, thedisplay shows “Err”.

2. Holddown [CAL] for about ve seconds to start calibration.

3. Whenthe display shows “CAL 1”, release thebutton and wait for

theactual slope to be displayed.

4. Turnthe spirit level through 180° and put it back on thesame surface.

5. Holddown [CAL] for about ve seconds and release thebutton when

“CAL 2” appears.

6. “CAL 2” ashes three times and thereading is displayed again.

Technical specification

Length600 mm

Accuracy, digital slope gauge± 0.2°

Accuracy of bubble vials± 0.5 mm/m

Measuring range0 to 90°

Units of measurement°, %, mm/m, in/ft

Environment for use0 °C to 40 °C

1

3

9

8 10 12

52

711

4

6

H=L·tan α

H=L/tan α

45°<< 90°α

Produktspezifikationen