Crest Audio Versarray 218 MKIII Bedienungsanleitung
Crest Audio
Lautsprecher
Versarray 218 MKIII
Lies die bedienungsanleitung für Crest Audio Versarray 218 MKIII (16 Seiten) kostenlos online; sie gehört zur Kategorie Lautsprecher. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Crest Audio Versarray 218 MKIII oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/16
1
Crest Audio® Versarray™ Mk III FlyQWIK™
Adjustable Rigging System
Crest Audio® Versarray™ VR218 Mk III Ground Stack Kit
Specifications and Instructions
CAUTION ! / a Before attempting to stack any 112 Versarray™ Mk III Pro onto cabinets Versarray™ 218
Mk Mk III / a Pro Sub, refer to qualified professional. The Versarray™ 218 III / Pro Sub and/or speaker
array can fall over from improper property suspension, resulting in serious injury and damage. Use only
the cor
rect mating the others. hardware. All associated rigging is responsibility of
Description
The Crest Mk Audio® Versarray™ VR218 III Ground Stack Kit is designed to to allow up three of the
Versarray™ Versarray™ 112 cabinets stacked Mk III / Pro to be above a 218 Mk III / Pro Sub for ground
stack use. Brackets
that the the interface the bolt to top of Versarray™ Pro 218 Mk III / Sub, to with
cabinet rigging hardware are
provided, provide as Strapping Plates well as to for strapping the Sub
cabinet down and securing the it to stage or
the round g are supplied.
This is it will if is Kit an and optional of piece the overall rigging system, not be needed there no need to
stack
VR™ VR™ 112 / Mk III Pro cabinets the on top of 218 Mk III / Pro Sub.
Specifications:
Contents: Two Strap Stacking one Brackets (L & R), Rear Pivot Bar Bracket, two Strapping
Plates (L & R).
All required the the push pins bolts are supplied on VR™ 218 Sub, and locking
needed are included on the VR™
112 M I / k I I Pro cabinets.
Height added to Versarray™ 218 4.93” Mk III / Pro Sub: (12.52 cm)
Material: thick solid 5 mm (approx. 7 Gauge) steel alloy.
Finish: All brackets and plates black coated paint have a flat powder finish.
Maximum 30 Combined Angle: than Total Stack Must be less degrees.
Maximu umbe abinet e ub mor h 3 maximumm N r of C s p r S : No e t an
Versarray™ 112 Mk III/ can Pro two-way speaker cabinets only be stacked on topof a Versarray™ 218 Mk
III / Pro Sub when the Sub is located on a substantially level surface, and secured to the stage or ground
with fety raps. sa st
CAUTION ! The Crest Mk Audio® Versarray™ III Ground Stack Kit is designed to be used ONLY in
con- / junction the with Versarray™ 218 Mk III Pro Sub the and Versarray™ 112 Mk III / - Pro two way
speaker
cabinets! t is ot esigned be sed ith ny er rands ubs tacking abinets! I n d to u w a oth b of S or s c
2
CAUTIONS:
IF ANY OF THE BRACKETS, RAILS, CABINET STRAPS, PIVOT BAR OR GROUND STACK BRACK-
ETS HAS BEEN DAMAGED OR DISTORTED, DO NOT USE, AND DO NOT STACK THE ARRAY UNTIL
THEY CAN BE REPLACED OR REPAIRED!
DO NOT USE THE PIVOT BAR OR ANGLE SLIDER BRACKET AS HANDLES TO TRANSPORT THE
CABINETS!
DO NOT TRANSPORT THE CABINETS IN ARRAY CONFIGURATION COUPLED TOGETHER, OR
WHILE STACKED ON TOP OF THE SUB.
TRANSPORT WITH THE RECOMMENDED TRANSPORT CART AND IN THE STIPULATED MANNER
FOR THAT CART IS THE ONLY APPROVED METHOD FOR TRANSPORTING THE CABINETS IN THE
ARRAY CONFIGURATION. TRANSPORT IN AN UNAPPROVED MANNER VOIDS THE WARRANTY,
AND THE SYSTEM WOULD BE CONSIDERED UNSAFE TO BE FLOWN AFTER SUCH AN UNAP-
PROVED TRANSPORT EVENT.
Correct use and seating of the Quick Release Push Lock Pins Used with most all Versarray™ rigging hardware
When using the Quick Release Positive Lock Pins, when the Quick Release Push Lock Pins are inserted, they
should be fully seated, so that the black shoulder near the end of the pin has been placed flush with the side of
the bracket, or as far in as the pin hole cavity will allow it to be inserted.
You will have to fully depress the center push-button to do this.
You should not be able to pull these pins center out the unless push-button is fully depressed.
The loudspeaker stacked on top of only accordance Crest Audio® Versarray™ models should be the Sub in
with
the the notices. procedures and limitations specified in User’s Manual and manual update possible
Do not at-
tempt to suspend/stack unless you have read and properly understood all instructions. This system
should be connected professional with certified rigging rigging hardware by an authorized and compliance in
with local,
provincial national or suspension ordinances. PROPER ALWAYS USE GRADE
HARDWARE.
Design and specifications subject to change without notice.
3
Crest Audio® Versarray™
VR Ground Stack Kit
Installation Procedure
Installation of each individual bracket and/or plate is started by the removal of the bolts on the top and
sides of the cabinet that correspond with the particular bracket being installed. There are 8 bolts on the top
of the cabinet and 2 on each side to be removed. A 6.0 mm Allen wrench (Hex Key) is required to remove
the bolts. See Fig. 1 – 4
Figure 1 2Figure
Figure 3 4Figure
Left Strap Stacking Bracket
1. After the two bolts have been removed, place the bracket into position. Orient it so that the ear is on the edge
of the cabinet. See Fig. 5
Figure 5
Produktspezifikationen
| Marke: | Crest Audio |
| Kategorie: | Lautsprecher |
| Modell: | Versarray 218 MKIII |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Crest Audio Versarray 218 MKIII benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lautsprecher Crest Audio
17 August 2024
7 August 2024
3 August 2024
2 August 2024
31 Juli 2024
31 Juli 2024
31 Juli 2024
29 Juli 2024
28 Juli 2024
27 Juli 2024
Bedienungsanleitung Lautsprecher
- Logic3
- Renkforce
- Yamaha
- Woxter
- Klip Xtreme
- Max
- Ashly
- MB Quart
- Exagerate
- Tascam
- Kinyo
- Lilliput
- Totem
- Thonet & Vander
- Fresh 'n Rebel
Neueste Bedienungsanleitung für -Kategorien-
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025