Crestron CLXI-2DIMFLV8 Bedienungsanleitung

Lies die bedienungsanleitung für Crestron CLXI-2DIMFLV8 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 8 Bewertungen. Hast du eine Frage zu Crestron CLXI-2DIMFLV8 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

CLXI-2DIMFLV8

0-10 Volt 8 Channel Dimmer Module, 2 Feeds, 230V

crestron.com

|

800.237.2041

>8 channels of 0-10 Volt dimming control for fluorescent ballasts

and LED drivers

>Two independent 4-channel dimmers in a single module

>Dual or single 230 Volt feed

>Arcless switching

>Air-gap relays on every channel output

>Override preset capability

>Convection cooled

>Occupies 1 module space in a CAEN or CAENIB

automation enclosure

>Easy termination using CLTI Series terminal block

>CEC Title 24 2013 Compliant

As part of a complete Crestron

®

lighting system, the CLXI-2DIMFLV8

lighting control module provides 8 channels of 0-10 Volt dimming control

for fluorescent ballasts and LED drivers. The CLXI-2DIMFLV8 is actually

composed of two independent 4-channel dimmers in a single module.

Each channel is rated for 20 Amps, with a total module rating of 40 Amps

when fed from two separate 20 Amp feeds. Air-gap relays are provided on

every channel output, allowing individual circuits to be serviced without

disabling the entire module.

CLXI Series dimmers are rigorously built for ultimate reliability. Split-

bobbin transformers and ground referenced electronics deliver superior

performance. Lamp flicker is minimized through Crestron’s innovative

zero-crossing detection technique backed by proprietary firmware. Low-

maintenance convection cooling assures quiet and trouble-free operation.

An override feature allows each channel to be adjusted to a preset state

during setup. In the event that Cresnet

®

communications should be

disrupted for any reason, a simple contact closure can be used to activate

the override presets on a global or semi-global basis.

The CLXI-2DIMFLV8 occupies a single module space in any or CAEN

CAENIB automation enclosure. Termination of high-voltage wiring to the

module is facilitated by a CLTI-2DIMFLV8 terminal block, sold separately to

enable termination of the wiring any time prior to installing the module.

CLXI modules are controlled by the or other 3-SeriesCLX-DIN-AP3

®

control system via the Cresnet network. A 5-wire link provides bussing of

the Cresnet and override signals between modules within an enclosure

(interconnect jumpers included).

SPECIFICATIONS

Load Ratings

Dimmer Channels: 8

Per Channel: 20 Amps

Per Group: Channels 1-4: 20 Amps;

Channels 5-8: 20 Amps

Module Total: 40 Amps

Load Types: 0-10 Volt fluorescent ballast or LED driver (4-wire)

Power Requirements

220-240 Volts AC, 50/60 Hz, line power

Connectors on Module

Module Interconnect: (2) 5-pin 0.156 inch headers;

Cresnet/Override interconnect ports;

Each connects to a CAEN-BLOCK or the adjacent CLXI-Series module using

the interconnect cable provided

Connections via CLTI Terminal Block (sold separately)

LINE 1 - 2: (2) DIN rail terminal blocks, brown, line power inputs

DIM 1 - 8: (8) DIN rail terminal blocks, red, channel outputs

N IN 1 - 2: (2) DIN rail terminal blocks, blue, line input neutrals

N OUT 1 - 8: (8) DIN rail terminal blocks, blue, channel output neutrals

Buttons

SETUP: (1) Pushbutton, for manual channel activation and TSID

LED Indicators

PWR: (1) Green LED, indicates line power is applied to the LINE 1 terminal

NET: (1) Yellow LED, indicates communication with the control system

1 – 8: (8) Red LEDs, each indicates the state of the corresponding channel

SETUP: (1) Red LED, indicates unit is in setup/manual mode

Environmental

Temperature: 32° to 104° F (0° to 40° C)

Humidity: 10% to 90% RH (non-condensing)

Heat Dissipation: 45 BTU/hr

Shown with CLTI series terminal block (sold separately) positioned on left side.

Produktspezifikationen