Crestron DM-RMC-4K-SCALER-C Bedienungsanleitung

Lies die bedienungsanleitung für Crestron DM-RMC-4K-SCALER-C (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 99 Personen als hilfreich bewertet und erhielt im Schnitt 4.1 Sterne aus 50 Bewertungen. Hast du eine Frage zu Crestron DM-RMC-4K-SCALER-C oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

DOGUIDE

DO Connect the Device

Connect the device as required for the application.

Connections, Left Side

Connections, Right Side

NOTE: The DM IN port is a PoDM+ powered device (PD) port and is also compatible with HDBaseT

®

PoE+.

In order for the device to receive PoDM+, the device requires connection to a DigitalMedia™

switcher or other equipment that has a PoDM+ power sourcing equipment (PSE) port. In order

for the device to receive HDBaseT PoE+, the device requires connection to equipment that has a

corresponding HDBaseT PoE+ PSE port. Any wiring that is connected to a PoDM+ or HDBaseT PoE+

PSE port is for intrabuilding use only and should not be connected to a line that runs outside of the

building in which the PSE is located.

Connection to the included power pack is not required when PoDM+ or HDBaseT PoE+ is used to

power the device.

NOTE: Connection of the CEN-SWPOE-16 to the POE IN ports of DMC-4K-CO-HD output cards in a

DigitalMedia switcher can provide PoDM+ power to up to seven DM-RMC-4K-SCALER-C devices.

NOTE: The LAN port can connect to an Ethernet switch only if the DM IN port does not connect to a

DigitalMedia switcher.

DM-RMC-4K-SCALER-C/DM-RMC-4K-SCALER-C-DSP

4K DigitalMedia 8G+

®

Receiver and Room Controller with Scaler

DO Install the Device

The Crestron

®

DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP can be mounted onto a

at surface or onto a rack rail.

Mounting onto a Flat Surface

Using four mounting screws (not included), mount the device onto a at surface such as a wall or a

ceiling.

Mounting onto a Wall

Mounting onto a Rack Rail

The DM-RMC-4K-SCALER-C and DM-RMC-4K-SCALER-C-DSP mount onto the front or rear rail of a

rack. Position either the left or the right mounting ange of the device so that the holes align with the

holes in the rack. Then, secure the device to the rack using two rack mounting screws (not included).

Mounting onto a Rack Rail

DO Check the Box

QTYPRODUCTPART NUM.

2Connector, 4-Pin2003576

2Connector, 5-Pin2003577

1Power Pack, 24 Vdc 1.25 A, 100-240 Vac2045870

COM:

To RS-232

device

IR 1–2:

To IR

controllable

devices

AUDIO OUT:

To balanced/

unbalanced

stereo line level

audio output

device

RELAY 1–2:

To relay

controllable

devices

Ground

LAN:

10BASE-T/

100BASE-TX

Ethernet to local

network device

DM IN:

From

DM

®

switcher,

transmitter, or other

DM device or from

HDBaseT

®

device

24 V:

1.25A MAX:

From

included

power pack

HDMI OUT:

To HDMI

®

display

Produktspezifikationen