Da-Lite ViewShare Advantage Retrofit 25055 Bedienungsanleitung
Da-Lite
Projektionsfläche
ViewShare Advantage Retrofit 25055
Lies die bedienungsanleitung für Da-Lite ViewShare Advantage Retrofit 25055 (20 Seiten) kostenlos online; sie gehört zur Kategorie Projektionsfläche. Dieses Handbuch wurde von 32 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 16.5 Bewertungen. Hast du eine Frage zu Da-Lite ViewShare Advantage Retrofit 25055 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/20
INSTRUCTION BOOK FOR
ViewShare Advantage Electrol Retrofit
2
Tools Required for Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Save These Instructions
Pre-Installation
Prior to Retroit installation, you will need to run a CAT5 or
CAT5e network cable from the motor end of your screen to
the area in which your computer will be located. THE CAT5
CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot
exceed 200 feet. See Pre-Installation of ViewShare Screen and
Roller Assembly and Camera and Speakerphone Installation
sections for additional details on CAT5 cable connections.
NOTE: It requires at least two people to install a ViewShare
Retroit.
⁄“ Socket Driver
with 6" Extension
⅛” Hex Key
(included)
#2 Phillips Screwdriver
3
Removal of Old Screen and Roller Assembly
1. Run the screen to the up position.
2. Remove the access door by removing the screws from each end
(Figure 1). Be sure to support the door during this step to avoid
injury. Lift the door slightly and pull away from the edge of the
case.
3. Unplug 3 or 4 wire motor connector and RJ22/45 cable (if
applicable) from the junction box. See Appendix A for motor type
details.
4. Remove retainer clip from the motor (Figure 2).
NOTE: Save retainer clip for use in the installation of the
ViewShare screen and roller assembly.
5. Loosen (but do not remove) four ¼ – 20 nuts securing pin end
bracket (opposite end from the junction box) to the case housing.
While supporting the screen and roller, slide the pin end bracket
towards the end of the case and remove the existing screen and
roller assembly (Figure 3).
NOTE: Some units may only have two nuts per bracket.
¼ 20 Nuts
Pin End
Bracket
¼ 20 Nuts
Figure 1
Figure 2 – Motor End
Figure 3
Access Door Screws
Retainer Clip
Produktspezifikationen
| Marke: | Da-Lite |
| Kategorie: | Projektionsfläche |
| Modell: | ViewShare Advantage Retrofit 25055 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Da-Lite ViewShare Advantage Retrofit 25055 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Da-Lite
2 Oktober 2024
27 September 2024
11 September 2024
5 September 2024
2 September 2024
1 September 2024
31 August 2024
17 August 2024
10 August 2024
10 August 2024
Bedienungsanleitung Projektionsfläche
- Elite ProAV
- Avers
- Duronic
- EPV
- NEC
- Oregon Scientific
- Elite
- Stewart
- Optoma
- Elite Screens
- Pyle
- Lumene
- Kodak
- AV:link
- EluneVision
Neueste Bedienungsanleitung für -Kategorien-
12 Oktober 2024
29 September 2024
20 September 2024
7 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024
4 September 2024
Celexon Ultramobile Plus Professional 194 x 146 Bedienungsanleitung
3 September 2024