DeWalt DW7050 Bedienungsanleitung

Lies die bedienungsanleitung für DeWalt DW7050 (2 Seiten) kostenlos online; sie gehört zur Kategorie Säge . Dieses Handbuch wurde von 28 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 4 Bewertungen. Hast du eine Frage zu DeWalt DW7050 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Extension Kit

DW7050, DW7080

WARNING: For your own safety, read the miter saw instruction

manual before using any accessory. Failure to heed these warnings

may result in personal injury and serious damage to the miter saw

and the accessory. When servicing this tool, use only identical

replacement parts.

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments or

accessories.

FOR MITER SAWS WITH U-SHAPED SUPPORTS (FIG. 1)

The extension kit can be used on either or both sides of the saw.

Assemble the extension kit as shown:

1. Install the self-tapping stud into the hole underneath the saw,

threading in the shorter end using a 1/2" (13 mm) wrench.

2. Install the stop-washer and screw into the rod nearest the front

(DW7050).

3. Clamp the rods against the miter saw unit by tightening the

clamping bracket nut.

4. Align end plate with top of work surface and tighten locknuts.

Kit de rallonges DW7050, DW7080

AVERTISSEMENT : Pour votre sécurité, lire le manuel de

l’utilisateur de la scie à onglet avant l’utilisation de tout accessoire.

Tout manquement à ces avertissements augmente les risques de

dommages corporels, et les risques de sérieusement endommager

la scie à onglet et ses accessoires. Lors de l’entretien de cet outil,

n’utiliser que des pièces de rechange identiques.

AVERTISSEMENT : Pour réduire tout risque de dommages

corporels graves, arrêter et débrancher l’outil avant tout

réglage ou avant de retirer ou installer toute pièce ou tout

accessoire.

Français

English

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

(MAR09) Part No. N022966 DW7050, DW7080 Copyright © 1996, 2008, 2009 DEWALT

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of

pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

FOR MITER SAWS WITH HOLES (FIG. 2)

1. Slide rods into the holes as shown in Figure 2A.

2. Align end plate with top of work surface and tighten locknuts.

3. Insert the self-tapping screw into hole to lock the rods in place

(Fig. 2B).

WARNING:Do not lift, support, or carry the miter saw by the

extension kit. To do so may cause tipping and loss of control,

leading to personal injury.

NOTE: Before transporting miter saw, remove the extension or

telescope it in toward the saw.

FIG. 1

FIG. 2A

HOLES

TROUS

ORIFICIOS

FIG. 2B

SELF-TAPPING

SCREW

VIS

AUTO-TARAUDEUSE

TORNILLO

AUTORROSCANTE

WARNIN

G:

AL

PROP

ERLY

B

RODS (2)

TIGES (2)

VARILLAS (2)

STOP WASHER

AND SCREW

RONDELLE

D’ARRÊT ET VIS

ARANDELA DE

TOPE Y

TORNILLO

SELF-TAPPING STUD

MONTANT

AUTOTARAUDEUR

TACHÓN

AUTORROSCANTE

CLAMPING BRACKET

DISPOSITIF

DE FIXATION

SOPORTE

DE FIJACIÓN

LOCKNUTS (2)

CONTRE-ÉCROUS (2)

CONTRATUERCAS (2)

ENDPLATE

BORD

PLACA TERMINAL

Produktspezifikationen