EK Water Blocks EK-FC R9-290X - Acetal+Nickel 2.0 Bedienungsanleitung
Seiten 2 Engels PC Kühlventilator
Lies die Bedienungsanleitung für EK Water Blocks EK-FC R9-290X - Acetal+Nickel 2.0 kostenlos online oder lade das PDF herunter. 33 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
All disclosures, notices and warranty conditions are being written on the EKWB website. Please read terms of use. Released on 15
th
of January 2014. Revision 1.1
Installation and mounting manual for EK-FC R9-290X water block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before
installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1.Please carefully read the manual before through before beginning with the installation process!
2.Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3.The EK High Flow and EK-PSC type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O-ring gaskets.
4.The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION.Sample picture of AMD Radeon R9 290X series graphics card.
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER: Remove encircled screw on the
bracket (required only on certain models):
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD
1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink assembly screws must
be removed. There are 16 screws on the back of the graphics card.
2.CLEANING THE PCB. Carefully detach the original stock cooler
after removing all screws securing it to the board. Wipe off the
remains (by using non–abrasive cloth or
qtip
, as shown on sample
photo) of the original thermal compound until the components and
circuit board are completely clean. EKWB recommends the use of
denatured alcohol for removing TIM leftovers.
3. APPLYING THERMAL COMPOUND. Wipe off the remains
(by using non–abrasive cloth or
q-tip
) of the original thermal
compound until the components and circuit board are
completely clean. Apply thermal compound: lightly coat
AMD
GPU chip with enclosed EK-TIM Ectotherm thermal grease.
EKWB recommends to apply thermal grease in cross form for
best performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, some of which are already pre-cut. Others
have to be cut to smaller chunks in order to cover all the VRM components such as MOSFETs and drivers.
PLEASE REMOVE THE PROTECTIVE FOIL FROM
BOTH SIDES OF THE THERMAL PADS PRIOR TO
INSTALLATION.
Replacement thermal pads:
Thermal Pad D – 0.5mm (RAM 16x),
Thermal Pad A – 1 mm (100x16mm)
STEP 3: INSTALLING THE WATER BLOCK
1.PLACING THERMAL PADS ON PCB.Place thermal pads on chips so that numbers on chips match size of thermal pads. EKWB made sure users have more than
enough pads to cover all surfaces that need to be covered to make block fully functional). EKWB recommends using small drops of electrically non-conductive (for
example: EK-TIM Ectotherm, Arctic Cooling MX-2 ™, MX-4 ™ or GELID GC-Extreme™) thermal grease on each phase regulator (that is being covered with thermal pad) in
order to even further improve the thermal performance of the EK-FC R9-290X block.
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
2
1: Thermal pad D – 0.5mm
(for memory IC):
2: Thermal pad A – 1mm
(for VRM/MOSFET):
1
1
1
1
1
1
1
1
2
Produktspezifikationen
| Marke: | EK Water Blocks |
| Kategorie: | PC Kühlventilator |
| Modell: | EK-FC R9-290X - Acetal+Nickel 2.0 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit EK Water Blocks EK-FC R9-290X - Acetal+Nickel 2.0 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung PC Kühlventilator EK Water Blocks
EK Water Blocks 3831109805138 hardware cooling accessory 3831109805138 Bedienungsanleitung EK Water Blocks EK-FC780 GTX Ti Bedienungsanleitung EK Water Blocks 3831109869079 Bedienungsanleitung EK Water Blocks 3831109869055 Bedienungsanleitung EK Water Blocks EK-D5 Bedienungsanleitung EK Water Blocks 3831109869086 Bedienungsanleitung EK Water Blocks EK-FC R9-280X DCII Bedienungsanleitung EK Water Blocks 3831109840665 Bedienungsanleitung
Alle EK Water Blocks PC Kühlventilator Bedienungsanleitungen
Beliebt in PC Kühlventilator
EK Water Blocks 3831109868966 Bedienungsanleitung EK Water Blocks 3831109869109 3831109869109 Bedienungsanleitung EK Water Blocks EK-RES X3 Bedienungsanleitung
Bedienungsanleitung PC Kühlventilator
Neueste Bedienungsanleitungen für PC Kühlventilator
Be Quiet! Pure Loop 120mm Bedienungsanleitung Iceberg Thermal IceSLEET G4 Bedienungsanleitung DeepCool LS520S Zero Dark Bedienungsanleitung Thermalright Royal Pretor 130 Ultra Bedienungsanleitung In Win MR36 Bedienungsanleitung Cooler Master SickleFlow Edge 120 ARGB Bedienungsanleitung StarTech.com SILVGREASE10-PRO Bedienungsanleitung Be Quiet! Pure Loop 2 FX 240mm Bedienungsanleitung Thermalright Core Vision 360 Bedienungsanleitung PCCOOLER RZ820 Bedienungsanleitung