Electro Harmonix Mainframe Bit Crusher Bedienungsanleitung
Electro Harmonix
Nicht kategorisiert
Mainframe Bit Crusher
Lies die bedienungsanleitung für Electro Harmonix Mainframe Bit Crusher (12 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 19 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 10 Bewertungen. Hast du eine Frage zu Electro Harmonix Mainframe Bit Crusher oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/12
1
Congratulations on your purchase of the MAINFRAME, a powerful but easy- -use to
sample rate reducer and bit crusher. Introducing old-school digital audio sounds
into your music has never been easier. A broad range of controls help you fine-
tune the digital artifacts, and the innovative Sample Rate Tuning Mode makes it
easy to match the sample reduction to a pitch, even on the fly. Access the
MAINFRAME and immerse your tone in the sounds of the arcades, consoles, and
terminals of yesteryear.
WARNING: Your Mainframe comes equipped with an Electro-Harmonix 9.6DC-200BI
power supply. The Mainframe requires at 9VDC with a center negative plug. Use 90mA
of the wrong adapter or a plug with the wrong polarity may damage your Mainframe and
void the warranty. Do not exceed 10 VDC on the power plug. Power supplies rated for .5
less than will cause the Mainframe to act unreliably. 90mA
- FEATURES -
Sample Rate Reduction ranging from 48kHz to 110Hz
Bit Depth Reduction ranging from -bit to 1-bit 24
Selectable High/Low/Band-Pass filter to shape the artifacts of the bit crushing
and sample rate reduction
Sample Rate Tuning Mode allows you to set the sample rate to match the key
of a song, or continu ly adjust the sample rate based on what you play on al
your instrument
Programmable preset or expression pedal setting allows you to save your
sound or control any combination of the Mainframe’s knobs with an external
expression pedal
Secondary knob parameters allow you to fine- tune the Mainframe’s effect
High quality buffered bypass and silent switching
- SPECIFICATIONS -
Audio input impedance: 2M
Audio o put impedance the OUTPUT jackut : 500
Current draw: mA 90
Maximum input signal level: 6.25 dBu (4.5V peak- -peak) to
2
C C ONTROLS AND ONNECTIONS
1. VOL Knob This knob sets the master output level of the Mainframe.
2. BLEND Knob This knob blends between the dry guitar signal and the
effect signal. As the knob is turned clockwise, the output ranges from
completely dry guitar to a fully effected signal with the filter applied.
3. BIT DEPTH Knob As this knob is turned clockwise, the bit depth of
the signal is
reduced
, producing a distorted, noisy tone.
4. SAMPLE RATE Knob As this knob is turned clockwise, the sample
rate of the signal is
reduced
, producing a ringing or glitchy tone.
5. FILTER HPF/BPF/LPF Switch This toggle switch controls the
direction of the Mainframe’s filter:
HPF: High-Pass Filter
BPF: Band-Pass Filter
LPF: Low-Pass Filter
3
6. FILTER FREQ This knob controls the frequency of the Mainframe’s
filter. As the knob is turned up, the frequency increases. The frequencies
cut/passed by the filter vary by the filter type:
HPF: Frequencies above the FREQ knob setting are passed,
frequencies below are cut.
BPF: The FREQ knob controls the center frequency of a pass band.
Frequencies above and below this center frequency are cut.
LPF: Frequencies below the FREQ knob setting are passed,
frequencies above are cut.
Tip: For a tone with no filtering, set the FREQ knob to maximum and set
the toggle switch to LPF.
7. FILTER PEAK This knob controls the resonance of the Mainframe’s
filter. Turning this knob clockwise increases the resonance, producing a
sharper, more cutting tone.
8. EXP / PRESET Button and Green LED This button turns expression
mode or a saved preset on and off. When the Green LED is lit, expression
control is enabled, or the preset is enabled. See pages 6- for details on 9
how to save expression settings or a preset.
9. Footswitch and Red LED Press and release the footswitch to toggle
between bypass and effect modes. When the red LED is lit, the Mainframe
is in effect mode. Double tap the footswitch to enter Sample Rate Tuning
Mode, and tap it once again to exit Sample Rate Tuning Mode and save
the tuned sample rate.
10. INPUT Jack This 1/4" phone jack is the audio input of the
Mainframe. The input impedance is 2M .
11. OUTPUT Jack This 1/4" phone jack is the main audio output of the
Mainframe The output impedance is 500 . .
12. EXP Jack Connect an expression pedal or control voltage jack to
allow for external control over every knob on the Mainframe See pages .
6- for a description on how to set up and control the Mainframe with an 9
external expression pedal.
13. 9V Power Jack Plug the output of the Mainframe’s supplied
EHX9.6DC 200mA AC adapter to the 9V power jack located at the top of
the pedal. The Mainframe requires 90mA at 9VDC with a center-negative
plug. Do not exceed 10.5VDC on the power jack.
Produktspezifikationen
| Marke: | Electro Harmonix |
| Kategorie: | Nicht kategorisiert |
| Modell: | Mainframe Bit Crusher |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Electro Harmonix Mainframe Bit Crusher benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Electro Harmonix
5 September 2024
5 September 2024
5 September 2024
4 September 2024
4 September 2024
3 September 2024
Electro Harmonix Germanium 4 Big Muff Pi Bedienungsanleitung
3 September 2024
3 September 2024
Electro Harmonix Deluxe Memory Man 550-TT Bedienungsanleitung
3 September 2024
28 August 2024
Bedienungsanleitung Nicht kategorisiert
- Orion
- Crivit
- Homelite
- Daitsu
- SKLZ
- Hameg
- Coolaroo
- Whitestone
- Babysense
- Ilford
- HuddleCamHD
- Ordex
- XYZprinting
- AXI
- Socket Mobile
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025