Elite Screens ZSP-TR01 Bedienungsanleitung
Elite Screens
Regler
ZSP-TR01
Lies die bedienungsanleitung für Elite Screens ZSP-TR01 (3 Seiten) kostenlos online; sie gehört zur Kategorie Regler. Dieses Handbuch wurde von 12 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 6.5 Bewertungen. Hast du eine Frage zu Elite Screens ZSP-TR01 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/3
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Wireless RF Projector Trigger Controller
Part# ZSP-TR01
User Guide
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
SPECIFICATIONS
1. Size and Weight: W x H x D: 4.8”x2”x0.7”, Weight: 0.09LBS
2. : 80 feet (25M) Max. Control Distance
Control Type: ASK / FSK
3. 15V Projector Output Support Trigger Voltage: 3－
4. 315Mhz, Power Below 2 milli-watts RF Spec. Frequency: ：
5. : Directions for user
a. Connect the wireless RF trigger controller and the projector as shown below.
b. Use the wireless RF trigger controller to synchronize the screen drop/rise with the
projection s power cycle via remote control according to the version number on ’
your screen. Version number can be located either on the screen’s end cap
sticker or on the outside sticker of the packaging box.
Location of version number
on end cap sticker.
Fig. 1
Location of version number
on packaging box sticker.
Fig. 2
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Note: Directions for synchronizing your 5-12V wireless trigger according to the
version number.
Version 1.4 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Push the small button located on the circuit board on the left side of the projection screen
(please note: you may require a small sharp object to achieve this After the light turns on, ). LED
press & hold the button on your Wireless RF Trigger Controller and make sure the LED light on UP
circuit board turns on.
Step 2: Continue to hold the button for an additional 3-4 seconds. After 3-4seconds, your 5- V up 12
Wireless Trigg should er be activated and you’ll be able to control your screen with your projector s ’
power cycle .
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around
20-30 seconds for full off and on cycle each time)
Version 2.0 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Make sure to unplug your screen from the power outlet
Step 2: Hold the UP button on your 5-12V wireless trigger
Step 3: While holding the button, plug the screen back to the power outlet UP
Step 4: Wait 5 seconds and then release the button UP
Step 5: Your 5-12V wireless trigger should now be activated with your screen and ready to be used
and able to control your screen with your projector s power cycle. ’
Repeat the steps again if not successful.
Note: Once your RF remote has been activated, th synchronization will be saved even the power e if
is cut off.
Fig. 3
Produktspezifikationen
| Marke: | Elite Screens |
| Kategorie: | Regler |
| Modell: | ZSP-TR01 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Elite Screens ZSP-TR01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Regler Elite Screens
23 August 2024
Bedienungsanleitung Regler
- Gefen
- Valcom
- One For All
- Gossen Metrawatt
- Rolls
- Vakoss
- Ltech
- Fusion
- Sven
- Sonifex
- Venom
- Adj
- Magnus
- BZBGear
- Dragonshock
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
5 Oktober 2024
4 Oktober 2024
3 Oktober 2024
1 Oktober 2024
Hori Force Feedback Truck Control System Bedienungsanleitung
1 Oktober 2024
30 September 2024
27 September 2024