Elkay EWF172 Bedienungsanleitung

Lies die bedienungsanleitung für Elkay EWF172 (105 Seiten) kostenlos online; sie gehört zur Kategorie Wasserspender. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 3 Bewertungen. Hast du eine Frage zu Elkay EWF172 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Page 197747C (Rev. N - 06/19)

WaterSentry

®

Water Cooler.

7. Turn on water supply and hold open the bubbler on

cooler until approximately 1 gallon of water is dis-

pensed.Thisushingprocedurepurgesairandne

carbonparticlesfromthelter.When1gallonofwater

has been purged through the cooler, carefully inspect all

water connections for leaks.

LK1141A Bubbler with or without a chiller unit, under

sink application.

1. Open inlet water supply valve, open dispensing valve

or bubbler and allow approximately 1 gallon of water to

bedispensed.Thisushingprocedurepurgesairand

necarbonparticlesfromthelter.

2. Turn dispensing valve off and carefully inspect all water

connections for leaks.

3. Unit is now ready for operation.

TheselterkitsaredesignedtobeusedwithavarietyofElkay

products including:

1.WaterCoolersandDrinkingFountains.(Note-ForBottleFiller

modelsuse51300C.)

2.LK1141ABubblerwithorwithoutachillerunit.

3.Independentlyinanundersinkapplication.Forundersink

applications, it is recommended that water be dispensed

through a dedicated valve or faucet instead of the sink faucet

duetothereducedowthroughthelter.

NOTICE: Do not use with water that is microbiologically

unsafe or of unknown quality without adequate

disinfection before or after the system.

General Installation Instructions

1.Theselterkitsmustbeinstalledincompliancewithall

state and local laws and regulations governing the

installation and use of this product. Maximum inlet water

temperature 100°F(38°C).

2.Mountlterheadinasuitablelocation,usingthelter

mounting bracket and screws supplied. Allow enough

roomunderthelterheadforinstallationandremovalof

ltercartridge(13"minimum).

3.Connectthecoldwatersupplytothelterthroughashut-off

valveand3/8"O.D.tubing(suppliedbytheinstaller).For

ease of servicing, the shut-off valve should be located within

easyreachofthelter.

NOTE:Theinletandoutletttingsuppliedaspartofthe

lterheadareJohnGuestSupersealttingsthataccept

3/8"O.D.tubingonthelterinletand1/4"O.D.tubingon

the outlet. They may be used with copper, semirigid nylon

or polypropylene tubing, with a rated working pressure

equal or greater than encountered in application. Do not

use soft or braided tubing.

4. CAUTION: If supply pressure will ever exceed 100 psi,

install a pressure regulator to limit the inlet pressure to

thelterto100psiorbelow.

DO NOT ATTACH HOT WATER LINE TO FILTER.

Tomakeconnectionsonthelterhead,loosenlocknut.Push

thetubeendpastbotho-ringstoapositivestopinthelter

headrecess-approx.1",locknutmayhavetobebackedout

alittlemore.Screwthelocknuthandtighttoseal(SeeFig.1).

Endsoftubingmustbecutsquareandfreeofburrsandsharp

ends that could cut or nick the o-rings.

5.Connecttheoutletoftheltertotheinletoftheunion

usingthe1/4"O.D.polytubingand1/4"unionsupplied.

6.Removelterfromcarton,removeprotectivecap,attachlter

tolterheadbyrmlyinsertingintoheadandrotatinglter

clockwise.

FIG. 2

FIG. 1

See Note 4: Screw the locknut hand tight to seal

Filter Replacement*

1. Turn inlet water valve off.

2. Open bubbler to relieve pressure build-up in the system.

3.Removelterfromheadbyrotatingltercounterclockwise.

4.Removenewlterfromcarton,removeprotectivecap;

capmaybeplacedonoldltertoreducethechanceof

waterspillingfromlterhousing.

5.Attachltertolterheadbyrmlyinsertingintoheadand

rotatinglterclockwise.

FILTER KIT

EWF172 WaterSentry

®

VII Kit

(Lead, Chlorine, Taste & Odor and Particulate Class I Reduction)

FOR COMMERCIAL USE ONLY

IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect

power to your unit before installing or replacing the lter.

TheWaterSentry

®

VIIlteristestedandcertiedbyNSFInternationaltoNSF/ANSI42and53for

thereductionofChlorine,TasteandOdor,ParticulateClassI,andLead.

Produktspezifikationen