EMOS M0502 Bedienungsanleitung
EMOS
Nicht kategorisiert
M0502
Lies die bedienungsanleitung für EMOS M0502 (64 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 34 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 17.5 Bewertungen. Hast du eine Frage zu EMOS M0502 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/64
2206000020_31-M0502 105 × 140 mm
www.emos.eu
M0502
GB Laser Distance Meter
CZ Laserový měřič vzdálenosti
SK Laserový merač vzdialenosti
PL Laserowy miernik odległości
HU Lézeres távolságmérő
SI Laserski merilnik razdalje
RS|HR|BA Laserski daljinomjer
DE Laser-Entfernungsmesser
UA Лазерний далекомір
RO Telemetru cu laser
LT Lazerinis atstumų matuoklis
LV Lāzera tālmērs
2
GB | LASER DISTANCE METER
The laser distance meter is designed to calculate surface, volume and to measure distance.
The device is only designed for personal use; not for use by professionals. Any other usage may lead
to damage and injury.
The manufacturer takes no responsibility for damage caused due to tampering with the laser device
and not following safety instructions.
Technical data:
Laser class: 2
Max. output power (P.max): <1 mW
Wavelength: 620–690 nm
Measuring distance: 0.05 m to 40 m
Measurement accuracy: ±2 mm
Measuring units: m, ft, in, m², ft², m³, ft³
Measuring time limit: 0.25 s
Automatic switch-o: after 3 minutes since
the last press of a button
Laser beam switch-o when measuring:
after 30 seconds
Operating temperature: 0 °C to +40 °C
Storage temperature: -20 °C to +65 °C
Power supply: 2× 1.5 V AAA (not included)
Weight: 65 g (without battery)
Dimensions: 110 × 40 × 25 mm
Button description:
1
25
36
4
7A
7B
1 – ON button (turn on, measure)
2 – UNITS button (switch between meter
functions)
3 – C/OFF button (reset values, turn o)
4 – water-level
5 – button for adding up/subtracting values,
measurement memory
6 – button for changing measuring point
7A, 7B – measuring point
Battery compartment:
3
Note:
Never point the laser on persons or animals.
Never look directly into the laser, it can damage your eyes.
Inserting Batteries
Remove the battery cover at the rear of the meter.
Insert 2× 1.5 V AAA batteries. Always use alkaline batteries only, not rechargeable ones.
Replace the battery cover.
Turning the Device On/O
Turn on the device by long pressing the ON button.
Turn o the device by long pressing the C/OFF button.
Distance Measurement/Changing Measuring Point
Long press the ON button.
An acoustic signal will sound and the screen will turn on.
Measurement starts in point 7B; the icon will be displayed.
If you wish to change the measuring point to 7A, press the button; the icon will be displayed.
Hold the device horizontally in front of the wall towards which you wish to measure distance.
The device must point to the wall at a right angle.
To this end, use the water-level. The bubble in the water-level must be in the middle between the
black lines.
The device will focus the laser on the wall; the icon will be displayed.
Then, press the ON button again. The device will measure the distance and show the distance on the
screen (the laser icon will disappear).
Changing Measuring Units
The default measuring unit is meter = m.
If you wish to change the measuring unit, repeatedly long press the button.
You can set the following measuring units: m, ft, in.
Continuous Distance Measurement
Long press the ON button.
An acoustic signal will sound and the screen will turn on.
Again long press the ON button; the device will start measuring continuously and the icon will
be displayed.
The screen will display measured max. and min. values. The values will change as you move the device.
The bottom portion will display the currently measured value; see the picture.
The device will emit an acoustic signal throughout the duration
of continuous measurement.
You can temporarily pause continuous measurement by short pressing
the ON button.
Long press the ON button if you wish to proceed with continuous
measurement.
End continuous measurement by pressing the C/OFF button.
Produktspezifikationen
| Marke: | EMOS |
| Kategorie: | Nicht kategorisiert |
| Modell: | M0502 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit EMOS M0502 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert EMOS
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Reloop
- HomePilot
- Clingo
- Warwick
- Roesle
- Ordex
- MuxLab
- Hogue
- Calex
- Hasbro
- Jokari
- Finlux
- VS Sassoon
- Skullcandy
- Erica Synths
Neueste Bedienungsanleitung für -Kategorien-
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025
4 Juli 2025