ESQ Analog Chronograph with Alarm Bedienungsanleitung
ESQ
betrachten
Analog Chronograph with Alarm
Lies die bedienungsanleitung für ESQ Analog Chronograph with Alarm (1 Seiten) kostenlos online; sie gehört zur Kategorie betrachten. Dieses Handbuch wurde von 24 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 12.5 Bewertungen. Hast du eine Frage zu ESQ Analog Chronograph with Alarm oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
Operating Instructions
Analog Chronograph with Alarm
1 2 3
H
E
C
D L
B
A
M
S
G
To activate/deactivate alarm:
Use push-button Cto toggle alarm on and off:
Two audible beeps indicate Alarm function is turned on; one beep
signals Alarm is turned off.
When Alarm sounds at set time, press button Cto stop beeping.
Chronograph Function Overview
Use push-buttons Aand Bto operate the chronograph.
NOTE: After 5-1/2 hours of continuous running, chronograph will
stop and reset automatically to conserve battery.
IMPORTANT: Crown must be in position 1 and hands must be at
zero before chronograph is started. If necessary, press button B
to reset hands to zero before beginning timing.
IMPORTANT: Do not push button Aor Bwhile crown is pulled to
position 2 or 3. If button Aor Bis accidentally activated while crown
is not flush against case, one or more of the chronograph hands will
become desynchronized. Should this occur, see directions below for
synchronizing hands.
Simple chronograph functions:
To measure the duration of a single, non-stop event:
1. Press button Ato start chronograph.
2. Press button Aa second time to stop chronograph, read
chronograph hands Eand Gto determine elapsed time.
3. Press button Bto reset chronograph to zero.
Split-time or intermediate time functions:
To take intermediate time readings as a race progresses:
1. Press button Ato start chronograph.
2. Press button Bto momentarily stop chronograph.
3. Read off the intermediate time.
4. Press button Bto resume chronograph function.
Hands will catch up with ongoing event.
5. To read a second split time, press button Bagain.
Repeat steps 2 through 4 to take any additional split times.
6. Press button Ato stop chronograph.
7. Take a reading of the final time.
8. Press button Bto reset chronograph hands to zero.
Synchronizing hands on Analog Chronograph with Alarm:
After changing the battery, or in the event of an error, the
chronograph hands can be realigned to zero if needed.
With crown in position 1, flush against case:
1. Press and hold buttons Aand Bsimultaneously for approximately
2 seconds to enter corrective mode.
2. Use button Bto realign chronograph minute counter hand E.
3. Use button Ato realign chronograph seconds hand G.
4. Press and hold buttons Aand Bsimultaneously to exit corrective
mode, with 2 chronograph hands now properly synchronized
at 12 o’clock/zero position.
Legend:
L - Alarm hand (12-hour)
H - Hour hand
M - Minute hand
S - Small seconds hand
E - Chronograph 30-minute counter
G - Chronograph seconds hand
D - Date window
1, 2, 3 - Crown positions
A - Chronograph push-button (start/stop)
B - Chronograph push-button (split/reset)
C - Alarm on/off push-button
A chronograph combines two time-keeping functions. It incorporates
a device to measure intervals of time independent of the regular time
shown on the dial. Your ESQ SWISS Analog Chronograph with Alarm
features a 30-minute counter, 12-hour alarm, and date display. It can
be used to time events up to 5 hours and 30 minutes in duration to
the nearest second.
To set the time:
1. Pull crown out to position 3.
2. Rotate crown in either direction to move hour Hand minute
Mhands to correct time.
3. Push crown back in to position 1.
To set the date:
CAUTION: Never set the date between 9:00 PM and 12:30 AM
when automatic calendar changes are taking place. Doing so could
damage the mechanism.
1. Pull crown out to position 2.
2. Rotate crown clockwise until correct date appears in window D.
3. Push crown back in to position 1.
To set alarm:
1. Pull crown out to position 2.
2. Turn crown counterclockwise until alarm hand Lis pointing to
desired time on bezel.
3. Push crown back in to position 1.
Produktspezifikationen
| Marke: | ESQ |
| Kategorie: | betrachten |
| Modell: | Analog Chronograph with Alarm |
Brauchst du Hilfe?
Wenn Sie Hilfe mit ESQ Analog Chronograph with Alarm benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung betrachten ESQ
16 August 2024
13 August 2024
11 August 2024
11 August 2024
10 August 2024
10 August 2024
Bedienungsanleitung betrachten
- Sinn
- Bruno Söhnle
- Timer
- Beper
- Boss
- TomTom
- Victorinox
- TW Steel
- Dugena
- Spin Master
- Ebel
- Westfalia
- MarQuant
- Alessi
Neueste Bedienungsanleitung für -Kategorien-
9 Oktober 2024
7 Oktober 2024
7 Oktober 2024
6 Oktober 2024
6 Oktober 2024
5 Oktober 2024
4 Oktober 2024
4 Oktober 2024
4 Oktober 2024
