EtherWAN EX17008A Bedienungsanleitung
Lies die bedienungsanleitung für EtherWAN EX17008A (2 Seiten) kostenlos online; sie gehört zur Kategorie Schalter. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 7.5 Bewertungen. Hast du eine Frage zu EtherWAN EX17008A oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Copyright 2020 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX17008A
02/25/2020
W70G-E17008AQ3
1 Unpacking
Unpack the items. Your package should include:
One EX17008A unmanaged switch
One AC power cord
One CD containing this user’s guide
If items are missing or damaged, notify your
EtherWAN representative. Keep the carton and
packing material.
2 What Else You Need
Category 5 or better Ethernet cables
3 Select a Location
Desktop installations: Mount on a flat table
or shelf surface.
Rack installations: Use a 19-inch (48.3-
centimeter) EIA standard equipment rack
that is grounded and physically secure.
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient temperature
between 0 and 40ºC (32 and 104ºF).
Do not cover fans on the rear and side.
Keep away from heat sources, sunlight, warm
air exhausts, hot-air vents, and heaters.
Be sure there is adequate airflow.
Keep the switch at least 6 ft (1.83 m) away
from the nearest source of electromagnetic
noise, such as a photocopy machine.
4 Connect to the Data Ports
The switch is equipped with eight 10/100 Mbps
RJ-45 port that provide IEEE802.3at Power over
Ethernet (PoE), with up to 30 Watts per port (50
- 57VDC, 600mA Max.) These ports can be
connected to PoE devices such as IP surveillance
cameras or Voice Over Internet Protocol (VoIP)
phones.
A. Insert one end of a Category 5 or better
Ethernet cable into a switch port.
B. Connect the other end into the Ethernet port
of the device.
C. Repeat steps A and B for each additional
device you want to connect to the switch.
5 Apply AC Power
A. Connect the female end of the supplied AC
power cord to the power receptacle on the
switch rear panel. Connect the other end to
a grounded 3-pronged AC outlet.
B. On the switch rear panel, move the ON/OFF
switch to the ON position.
When you apply AC power:
All green PoE and Link/ACT LEDs blink
momentarily.
The fans start.
The yellow Power LED goes ON.
The Link/ACT LEDs for every port connected
to a device flash, as the switch conducts a
brief Power On Self-Test (POST).
6 Front Panel LEDs
LED
Color
Status
Power
Yellow
ON = switch is receiving power.
PoE
(port number)
Green
ON = Power Device (PD) is connected.
OFF = PD is disconnected.
Link/ACT
(port number)
Green
ON = valid network connection.
OFF = no data transmission on port.
Flashing = port is sending or receiving
data.
Congratulations! You have successfully
installed your switch.
EX17008A Unmanaged Switch Installation Guide
Produktspezifikationen
| Marke: | EtherWAN |
| Kategorie: | Schalter |
| Modell: | EX17008A |
Brauchst du Hilfe?
Wenn Sie Hilfe mit EtherWAN EX17008A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schalter EtherWAN
5 November 2025
5 November 2025
5 November 2025
4 November 2025
4 November 2025
4 November 2025
3 November 2025
3 November 2025
3 November 2025
3 November 2025
Bedienungsanleitung Schalter
- IPGARD
- BZBGear
- Vimar
- Chacon
- Swisson
- Hikvision
- Toolcraft
- Buffalo
- SEADA
- STI
- EVE
- One For All
- Crestron
- Lancom
- GEV
Neueste Bedienungsanleitung für -Kategorien-
16 Januar 2026
13 Januar 2026
11 Januar 2026
10 Januar 2026
10 Januar 2026
10 Januar 2026
9 Januar 2026
5 Januar 2026
2 Januar 2026
28 Dezember 2025