Eureka N!ergy 1310 Bedienungsanleitung

Lies die bedienungsanleitung für Eureka N!ergy 1310 (2 Seiten) kostenlos online; sie gehört zur Kategorie Zelt. Dieses Handbuch wurde von 37 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 19 Bewertungen. Hast du eine Frage zu Eureka N!ergy 1310 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Fly pole

Roof poles

Center roof

pole

Center

Wall poles

Corner

Wall poles

Component List:

1 Wired Tent Body with Guy Ropes, 6 Wall Poles, 3 Roof Poles, 1 Fly Pole, 1 Fly,

1 Divider Curtain, 1 Carry Bag, 1 Stake Bag/Stakes and 1 Pole Bag

2. Assemble the shock corded

polesand divide according to size

and shapeTake care; make sure .

that each pole section is fully

seated into the next. Do not allow

the sections to snap together as

this can damage the ends.

See fig 2.

1. Remove from the carry bag and separate all the components. Unroll and unfold the

fabric top side up, on a clean, dry space and open the doors. If windy, stake down the

windward corner. See fig 1.

4. Start on one side and insert black wall poles into the corner elbowsAt Raise the tent..

the bottom of each pole, insert the pin/ring (attached to the corner web) into the bottom

of each pole. Next, install a blue pole at the center. With the blues, it works best to insert

the ring/pin first and then fit the pole into the elbo See fig 4.w.

Repeat on the other side until

the tent is at full height

and freestanding.

5. to the wall poles. See fig 5.Attach all clips

Stake the tent down through the corner web loops. Stake opposite corners while

applying tension to smooth the floor wrinkles. Next, align the center poles and stake

down. Do this before you add the fly. See fig 6.

6. Attach the fly to the pole. ,Lay out the fly with the inside side up on ground at the

front of the tent. Fit the fly pole into the pockets sewn to the hemThe pole runs from .

side to side down the center of the fly. Secure the fly to the pole by wrapping the hook

& loop fasteners around the fly pole. See fig 7, 8 and 9.

7. Attach the fly to the tent. Turn the fly assembly over and align it

so that the pole ends point to the side windows. Grasp the corners

of the of the fly and drag them up and over the roof poles to

completely cover the roof. (This is much easier with two people.)

The end of the poles should point out over the windows.

At the corners of the tent, reach under the fly and attach the hook &

loop straps to the wall poles, securing the fly in place. See fig 10.

At the bottom/corners of the tent, attach the shockcorded J-hooks

to the nylon rings on the corner web loops. See fig 11.

8. and adjust tension with the Stake out the attached guy ropes

in-line slidersAlso, there is a vent beneath each of the side .

windowsAttach the included cords and stake out. See fig 12..

Assembly Instructions

for the N!ergy 1310 Tent

YOUR TENT IS READY !

C

BAE

FD

fig 2

fig 1

fig 5

fig 3

fig 6

fig 11

fig 12

fig 7

fig 8fig 9

fig 10

3. into the sleeves sewn on the tent bodyInsert both black roof poles . They should run

corner to corner crossing in the center.

Fit one end of each into a nylon elbow attached to the roof corners at and . Move to A B

the opposite side, arch the poles and again fit into the nylon elbows at and . C D

Insert the blue roof pole, front to back, into the tan color coded sleeves from to . E F

See fig 3.

fig 4

REV. D 4.09

fig 14

green

blue

fig 13

E! Power System: To use, you will need a power source. Our E! Power Pak™ is sold

separately. Once connected to power, the control will display “green” at any switch that

is “ON” and the “ON” socket will glow blue. See fig 13.

E! Power Port: Open zipper and run extension cord through opening. Close zipper so that it

rests next to the extension cord. Make sure the zipper cover is not twisted or tuckedThe .

cover must lay flat against the outside of the tent to keep out rain.

Accessories: E! Power Fan/Light, E! Power Reading Light and an E! Power 12v

Adapter Cord.

Sweep Out: Inside, at the bottom of the

door is a sewn-in web loop. Pull this loop

to the outside and stake it down to

provide a ready exit for floor sweepings.

See fig 14.

Take Down: Pull up all stakes. Release the

fly’s hook & loop straps. Remove fly.

Remove fly poles. Remove clips from tent

poles and pull poles off of the pins.

Collapse all poles and sto Fold the tent w.

onto itself then fold the fly and lay it on

tent. Roll up both towards the open door

and stow.

Read the important safety instructions

on the reverse side.

NOTE:Although it is possible to pitch this tent alone, it is faster/easier with two people.

• Do not drop tent bg on its end Do not bounce tent bg on its end to get the ag or pole ba.a

tent outa. These actions may cut the shockcord and/or damge the pole ends.

•The N!ergTake care to keep them in y series tents are pre-wired with three 12V outlets.

their sleeves and void stepping on the sockets and wires during assembla y.

Produktspezifikationen