Eurolite LED Strip 4in1 Zone RF Controller Bedienungsanleitung
Eurolite
Nicht kategorisiert
LED Strip 4in1 Zone RF Controller
Lies die bedienungsanleitung für Eurolite LED Strip 4in1 Zone RF Controller (12 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 19 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 10 Bewertungen. Hast du eine Frage zu Eurolite LED Strip 4in1 Zone RF Controller oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/12
USER MANUAL
EN
No. 50531145 Receiver
Wireless remote control for single- and multi-colored LEDs 12-24 V
LED Strip 4in1 Zone RF Controller
No. 50531140 Set (receiver and remote control)
www.eurolite.de
•
Thank you for purchasing this LED control system. The wireless
receiver is especially designed for control of single- and
multi-colored (CW+WW, RGB, RGBW) LED strips requiring an
operating voltage of 12 V and 24 V direct current. The receiver is
operated by wireless control (2.4 GHz) via the remote control. 4
control zones are available. Multiple receivers can be assigned to
the zones as desired and controlled via the same remote control,
either separately or in groups. As the receivers forward the radio
signal, a large range can be covered and all color settings run in
sync. The maximum power consumption of a channel must not
exceed 6 A and of all LEDs connected 24 A. The connection must
be made by skilled personnel only. Please read these operating
instructions carefully before using the product. They contain
important information for the correct use of your product. Please
keep them for future reference.
•
Only use the product according to the instructions given herein. Damages due to
failure to follow these operating instructions will void the warranty! We do not assume
any liability for any resulting damage.
•
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the
warranty/guarantee will be null and void.
•
Unauthorized rebuilds or modifications of the product are not permitted for reasons of
safety and render the warranty invalid.
•
This product is not a toy. Keep it out of the reach of children. Do not leave packaging
material lying around carelessly.
•
Keep this device away from rain and moisture. Indoor use only.
•
Protect the product against excessive humidity and heat. The recommended
temperature is -5 to +45°C.
•
Before taking into operation, check upon possible damages. If defective, the product
must not be taken into operation.
•
This product is maintenance-free, except for occasional cleaning. You can use a
slightly dampened cloth for cleaning. Never use alcohol or solvents.
•
Maintenance and service operations are only to be carried out by authorized dealers.
INSTALLATION
•
Overview
Setup
•
Install the receiver in a suitable spot and remove the covers from the terminals.
•
Connect the LEDs to the negative and positive OUTPUT terminals (V+ = common positive pole,
V- = see figure on next page). The load by the LEDs must not exceed 6 A per channel. The
overall load must not exceed 24 A to avoid damage to the receiver.
•
For power supply, connect a regulated power supply unit (min. 12 V, max. 24 V) to the negative
and positive INPUT terminals.
•
Use the DIP switches to select the operating mode according to the connected LEDs:
RGB RGBW DIM CCT
•
Screw on the covers with the screws provided.
•
For power supply of the remote control, insert two 1.5 V AAA batteries into the battery
compartment as indicated.
•
For operation the receiver needs to be assigned to the remote control (see chapter “Wireless
Connection” on page 4).
DIP switch to select LED type
Power connection: 12-24V DC Connectors for LEDs
INSTALLATION
•
Application example 1: Single-color LEDs
V+→V+, CH1→V‒, CH2→V‒, CH3→V‒, CH4→V‒
Application example 2: White LEDs (CW+WW) with variable color temperature
V+→V+, CH1→CW, CH2→WW, CH3→CW, CH4→WW
Application example 3: RGB LEDs
V+→V+, CH1→R, CH2→G, CH3→B, CH4→not connected
Application example 4: RGBW LEDs
V+→V+, CH1→R, CH2→G, CH3→B, CH4→W
Produktspezifikationen
| Marke: | Eurolite |
| Kategorie: | Nicht kategorisiert |
| Modell: | LED Strip 4in1 Zone RF Controller |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Eurolite LED Strip 4in1 Zone RF Controller benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Eurolite
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 September 2024
5 September 2024
5 September 2024
31 August 2024
29 August 2024
21 August 2024
Bedienungsanleitung Nicht kategorisiert
- Generac
- Primewire
- Baccarat
- InLine
- Bellari
- Verbatim
- Casio
- Karma
- Bauhn
- Santos
- Fakir
- Ibiza Sound
- Havis
- Audient
- McGregor
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025