EXSYS EX-1338-2 Bedienungsanleitung

EXSYS Nicht kategorisiert EX-1338-2

Lies die bedienungsanleitung für EXSYS EX-1338-2 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu EXSYS EX-1338-2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/2

6 5

1338

English

1338

English

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Bedienungsanleitung

Vers. 1.2 / 19.06.13

Betriebs LED

S1-S8: 8 x 9 Pin Stecker Seriell RS-232

5V Buchse für

externes Netzteil

USB B-Buchse

PC-Anschluss

Die EX-1338-2 ist ein Modul zur Umsetzung von USB auf 8 RS-232 Schnittstellen mit

FIFO 16C550 Ports für den Anschluss von High Speed Seriellen RS-232 Peripherie

Geräten (z.B. Modem, Plotter usw.). Das USB Modul ist Hot Plug & Play fähig. Für die

Einstellungen der I/O Adressen und Interrupts sind keine Jumper und Einstellungen

notwendig. Sie werden vom System (BIOS) und beim installieren des Betriebssystems

automatisch vorgenommen. Die EX-1338-2 ist mit einem verschraubbarem Oktopus

Kabel ausgestattet.

Kompatibilität: USB 1.1 & 2.0

Betriebssysteme: WIN 9.x/ ME/ 2000/ XP/ Vista/ 7/ 8/ Server 200x/ Linux/ MAC

Anschlüsse: 8x 9 Pin D-Sub Stecker, 1x USB B-Buchse, 1x 5V Buchse

Lieferumfang: EX-1338-2, Treiber CD, Anleitung, USB Kabel, Oktopus Kabel

Zertikate:

CECE

CE / FCC / RoHS / WEEE DE97424562 / WHQL

ANSCHLÜSSE

ACHTUNG!!!

Nur zur Verwendung mit optionalem original Netzteil!

5 Volt Buchse:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Seriell 9 Pin D-SUB Stecker

DB 9M:

USB B-Buchse:

USB 2.0 B-Buchse

Pin Signal Pin Signal

1 VCC 3 DATA+

2 DATA- 4 GND

Achtung!

Stecker nie umge-

kehrt oder mit

Gewalt einstecken.

DRIVER INSTALLATION

Windows 2000/ XP/ Vista/ 7/ 8/ Server 200x

Windows will recognize a new „ “ and open the hardware assistant. FT232R USB UART

Please choose manual installation and put the driver CD into your CD-ROM drive. Enter

Path "D:\USB_to_IO\FTDI\(32_64bit)Win7_8_XP_Vista_2008_2008R2_2003_2000”

into the box for the Path/Source and click at >next/continue<. Now Windows search for

the drivers in the specied directory. Follow the hardware assistant and nish the instal-

lation. If Windows recognizes other new devices repeat the above described steps.

Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER

Click at <> < then enter and click at . In the windows Start Run “compmgmt.msc“ >OK<

that open select Under you should nd >Device Manager<. ”Ports (COM and LPT)“

one more new If you see this or similar entries „USB Serial Port (COM2) to (COM9)“.

the module is installed correctly.

INSTALL THE PERIPHERAL DEVICE

The speed from the serial ports can be set to the maximum baud rate of 115.2Kbaud.

With double click select for example >Device manager< >USB Serial Port (COM5)<.

Now you can select the dierent settings of baud rate, stop/start-bits etc. This setting

you can use also for the other COM ports.

CHANGE PORT NUMBER (NOT WIN98 & ME)

If you like to change the port number for example COM3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can choose

between COM3 up to COM256.

Windows 98/ 98SE/ ME

Windows will recognize a new and open the hardware assistant. “FT232R USB UART“

Please choose manual installation and put the driver CD into your CD-Rom drive (as

sample D:) . Now enter the Path into the box for the “D:\USB_to_IO\FTDI\Win98_ME”

Path/Source and click at . Now Windows search for the drivers in the >next/continue<

specied directory. Follow the hardware assistant and nish the installation. If Windows

recognizes other new devices repeat the above described steps. Attention! Restart

Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER

Click at <> < then enter and click at . In the windows Start Run “compmgmt.msc“ >OK<

that open select Under you should nd >Device Manager<. ”Ports (COM and LPT)“

one more new If you see this or similar entries „USB Serial Port (COM2) to (COM9)“.

the module is installed correctly.

INSTALL THE PERIPHERAL DEVICE

The speed from the serial ports can be set to the maximum baud rate of 115.2Kbaud.

With double click select for example >Device manager< >USB Serial Port (COM5)<.

Now you can select the dierent settings of baud rate, stop/start-bits etc. This setting

you can use also for the other COM ports.

HARDWARE INSTALLATION

Because there are large dierences between PC’s, we can give you only a general

installation guide. Please refer your computer’s reference manual whenever in doubt.

1. Connect the USB cable to the USB B-Port.

2. Connect the optional power supply into the 5Volt connector.

3. Now connect the other end from the USB cable (A-Plug) to the A-Port at your PC.

DRIVER INSTALLATION

LINUX

There are drivers available for Linux. The drivers are located in the folder

“D:\USB_to_IO\FTDI\Linux x86_64“ on the driver CD. They are supported by the most

versions of Linux. Because each individual distribution and kernel version of Linux is

dierent, sadly we cant provide a installation instruction. Please refer to the installation

manual for standard I/O ports from your Linux version.

MAC

There are drivers available for MAC. The drivers are located in the folder

“D:\USB_to_IO\FTDI\MAC OSX or Mac_OS_9_8“ on the driver CD. They are sup-

ported by the most versions of MAC OS. Because each individual version of MAC OS is

dierent, sadly we cant provide a installation instruction. Please refer to the installation

manual for standard I/O ports from your MAC OS version.

CLEANING

For cleaning please use only a dry u less cloth and remove the dirt with gently pres-

sure. In the area of the connectors please make sure that no bres from the cloth re-

main in the connectors. Attention! Never use a moist or wet cloth for cleaning!

Produktspezifikationen

Marke:	EXSYS
Kategorie:	Nicht kategorisiert
Modell:	EX-1338-2
Breite:	150 mm
Tiefe:	70 mm
Gewicht:	500 g
Produktfarbe:	Black, Grey
Übertragungstechnik:	Kabellos
Höhe:	30 mm
Betriebstemperatur:	0 - 55 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Zertifizierung:	CE, FC, ROHS, WHQL
Plug & Play:	Ja
Mac-Kompatibilität:	Ja
Kompatible Betriebssysteme:	Win 98SE, ME, 2000, Server 2003, XP, Vista\nLinux\nMac OS
Unterstützte Protokolle:	TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Anzahl serielle Anschlüsse:	8
Hostschnittstelle:	USB
Weitere Anschlüsse:	1x USB B-female\n8x 9-pin D-SUB serial male
Datenübertragungsrate:	0.1 Mbit/s
Anzahl Anschlüsse:	8
Chipsatz:	FTDI