Extron NetPA 204 POE Bedienungsanleitung
Lies die bedienungsanleitung für Extron NetPA 204 POE (6 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Extron NetPA 204 POE oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6
1
NetPA 204 POE • Setup Guide
IMPORTANT NOTE:
Go to www.extron.com for the complete NetPA 204 POE user guide, and specications before
connecting the product to the power source.
This guide provides quick start instructions for an experienced installer to set up and operate the Extron NetPA 204 POE network
power amplier. The Dante-enabled amplier receives up to four channels of audio via its AT (PoE++) port and drives up to
20 watts per channel into 8Ω or 4Ω speaker loads. The amplier is powered via Power over Ethernet (PoE).
Installation
Step 1 — Mounting
Turn o or disconnect all equipment power sources and mount the unit as required with either the included MBU 123 Low-Prole
Mount Kit or the optional ATB 100 Amplier Tile Bridge Ceiling Mount Kit (which can mount the amplier above ceiling tiles, out of
sight and near the speakers).
Step 2 — Making Rear Panel Connections
NetPA 204 POE
R
CLASS 2 WIRING
8Ω/4Ω OUTPUTS
REMOTE
PoE POWER
+
+
+
CONFIG
G
MUTE
LINK
A T (PoE++)
4
3
2
1
AAACCC DDD BBB EEE
Figure 1. NetPA 204 POE Rear Panel
A
AT (PoE++) — Connect an RJ-45 connector to communicate with both the Dante network and a
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568B
TP Wires
12345678
Pins:
computer running the Extron DSP Configurator Pro software. The Link LED indicates when a Dante
sync connection is made.
B
8Ω/4Ω OUTPUTS 1 through 4 — Connect up to four 2-pin,
CLASS 2 WIRING
8Ω/4Ω OUTPUTS
1
2
3
4
5mm captive-screw connectors to the speaker outputs.
ATTENTION:
• Use ‘Class 2 Wiring’ to connect speakers to
the amplier output.
• Utilisez un câblage de classe 2 pour connecter
les enceintes à la sortie de l’amplicateur.
C
REMOTE port — To mute all four outputs, jump the MUTE pin to the ground (G) pin on this 2-pole 3.5mm captive
REMOTE
G
MUTE
screw connector. Remove the jump to unmute the output (output audio).
D
CONFIG(uration) port — Connect a PC or other controlling device into the amplifier via this USB-C connector for
configuration of the amplifier using Extron DSP Configurator Pro software.
E
Reset button and LED — Initiates reset modes (see the NetPA 204 POE User Guide for details).
2
Step 3 — Powering the Amplier
Reconnect all the power cables and switch on the rest of the equipment before powering the power amplier. The front panel
Power LED (see gure 2,
1
) blinks green for up for up to 10 seconds as the amplier boots. There is a delay before the Power
LED starts blinking as PoE power is negotiated between your switch or power injector and the amplier.
NetPA 204 POE
LIMITER/PROTECT
SIGNAL
NETWORK POWER AMPLIFIER
4321
L
111 333
222
Figure 2. NetPA 204 POE Front Panel
NOTE: When the Dante controller sends an identify device request to the amplier, the Power LED blinks amber for 30
seconds. Once this sequence has completed, the LED will resume its previous indication. See Identifying a device on
page 4 for more details.
Once the boot-up sequence is complete, the amplier takes more time to sync with the Dante network, and begin the playback of
streamed content.The front panel Power LED (
1
) lights green.
Indications
2
LIMITER/PROTECT LEDs (see figure 2) — Indicate that an amplified output protection mode status as follows:
• A protective condition such as DC protect or thermal limiting exists.
• Digital clipping is occurring on the output channel.
3
SIGNAL LEDs — Lights when the output from a DSP channel, which goes to an amplier channel, crosses the signal
detection threshold (-59 dBFS) of the DSP.
4
PoE LEDs (on the rear panel, see the graphic, at right) — Indicate the status of PoE as follows:
PoE POWER
+
+
+
444
+
+
+
802.3bt (Power Class 5) PoE++ — All 3 LEDs are lit, 40W available
802.3at (Power Class 4) PoE+ — This LED and the bottom LED are lit, 25.5 W available
802.3af (Power Class 3) PoE — Only the bottom LED is lit, 12.95 W available
Step 4 — DSP Congurator Pro Software Installation
There are no hardware controls for the NetPA 204 POE. Control is via either Extron DSP Congurator Pro software or SIS
commands. To learn about full computer requirements, see the DSP Congurator Pro product page on www.extron.com.
Download DSP Configurator Pro from the Extron Website
1. From the Extron home page (www.extron.com), hover over the Download tab to open the Download page.
2. Click Software (located on the left side of the page). The Search Software eld appears.
3. Enter DSP Congurator Pro in the Search Software eld. The DSP Congurator Pro Software product page opens.
4. Click the Download button and follow the on-screen instructions.
NOTE: An Extron Insider account is required to download DSP Congurator Pro.
Produktspezifikationen
| Marke: | Extron |
| Kategorie: | Empfänger |
| Modell: | NetPA 204 POE |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extron NetPA 204 POE benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Extron
1 August 2025
30 Juni 2025
29 Juni 2025
29 Juni 2025
1 Oktober 2024
24 September 2024
12 September 2024
6 September 2024
6 September 2024
6 September 2024
Bedienungsanleitung Empfänger
- Williams Sound
- Topping
- RME
- Simaudio
- Bush
- Caliber
- Match
- Belkin
- Ground Zero
- Valcom
- Cayin
- Zgemma
- MIPRO
- Comtek
- Tangent
Neueste Bedienungsanleitung für -Kategorien-
1 August 2025
1 August 2025
1 August 2025
1 August 2025
1 August 2025
1 August 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025