Extron V-Lock Bedienungsanleitung
Extron
Lautsprecherunterstützung
V-Lock
Lies die bedienungsanleitung für Extron V-Lock (8 Seiten) kostenlos online; sie gehört zur Kategorie Lautsprecherunterstützung. Dieses Handbuch wurde von 35 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 18 Bewertungen. Hast du eine Frage zu Extron V-Lock oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
User’s Guide
Replacement accessory for Extron System INTEGRATOR®
SI 3 Surface Mount Speakers
68-1490-01
Rev. A
03 08
V-Lock™ Wall Mount Assembly Kit
V-Lock™ Wall Mount Assembly Kit • Introduction
Introduction
1
Figure 1 — V-Lock Assembly packaging details
Packaging Information
The V-Lock™ Assembly Kit contains two individually packed
wall mount assemblies (one for each speaker) and an Allen hex
tool.
Allen Hex Tool
Wall Mount
Assemblies
Outer
Packaging
About the V-Lock Assembly Kit
The V-Lock Wall Mount Assembly Kit is a pair of replacement
wall mount assemblies (wall plate and V-lock groove only) for
the Extron System INTEGRATOR® SI 3 surface mount speakers.
V Lock
Groove
(Stage)
Hex Lock
Screw
Pivot
Ball
Wall
Plate
Wi ngri
Access
Hole
Secondary
Mounting
Holes (4)
Primary
Mounting
Holes (2)
Figure 2 — Main parts of the V-Lock Assembly Kit
V-Lock™ Wall Mount Assembly Kit • Installation
Installation
2
Installing the V-Lock™ Assembly Kit
If your speakers are not already installed, follow the instructions
outlined in the supplied with the speakers (or SI 3 User's Guide
online at www.extron.com).
If your speakers are already installed, replace the V-Lock
assembly by following the instructions, below.
N Referring to packaging information for location,
carefully remove and check contents before installation.
N Extron recommends that the wiring installation is
performed by a professional audio equipment installer.
N For speaker details, specifications, troubleshooting tips,
and service access information, refer to the
SI 3 User's Guide supplied with the speakers, or online
at www.extron.com.
Existing wall mounting application
To replace a damaged V-Lock assembly that is already installed,
do the following:
1. Remove the Extron logo from the front of the speaker to
access the hex cap screw. Retain the logo.
2. Insert the hex tool and unlock the speaker.
3. Carefully lift the speakers away from the bracket, then
disconnect the seismic cable and audio wires from the rear
of the speakers.
To remo (or insert) the wires,ve
push down on the spring terminals
at the back of the speaker.
Release the springs to secure.
INPUT
Positive Wire
Negative
Wire
Figure 3 — Remove audio wires from the terminals
N If the ends of the wires are damaged and need to be
re-stripped, follow the instructions in the S I 3 User's
Guide.
Produktspezifikationen
| Marke: | Extron |
| Kategorie: | Lautsprecherunterstützung |
| Modell: | V-Lock |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extron V-Lock benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lautsprecherunterstützung Extron
6 September 2024
6 September 2024
Bedienungsanleitung Lautsprecherunterstützung
- Dynaudio
- Crestron
- My Wall
- Definitive Technology
- Bose
- Gravity
- LD Systems
- Electro-Voice
- Tannoy
- Vivolink
- Nedis
- Vonyx
- Bell'O
- Sanus
- Jamo
Neueste Bedienungsanleitung für -Kategorien-
4 Oktober 2024
30 September 2024
18 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024