Fluke MP1 Bedienungsanleitung
Lies die bedienungsanleitung für Fluke MP1 (5 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 58 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 29.5 Bewertungen. Hast du eine Frage zu Fluke MP1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
PN 4584021
September 2015
2015 Fluke Corporation. All rights reserved.
Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
MP1
Magnet Probe
Instruction Sheet
Introduction
The MP1 Magnet Probe (the Probe or Product) is an accessory with a
magnetic tip for 4 mm safety test leads. The magnet tip provides ic
contact to a ferromagnetic metal surface in areas with limited access
such as the carbon steel n RCDs or circuit breakers. screws o
The probe ts into recessed screw holes with a diameter of 6 . ≥mm
The probe CAT IV 600 V/CAT III 1000 V rated with a maximum is
current of 4 A.
fig_MP1.eps
Contacting Fluke
To contact Fluke, call one of the following telephone numbers:
• Technical Support USA: 1-800-44- -800-443-5853) FLUKE (1
• Calibration/Repair USA: 1-888-99- -888-993-5853) FLUKE (1
• Canada: 1-800- -F -800-363-5853) 36 LUKE (1
• Europe: +31 402-675-200
• Japan: +81-3- -3114 6714
• Singapore: +65-6799-5566
• Anywhere in the world: +1-425-446-5500
Or, visit Fluke's website at www.uke.com.
To register your product, visit . http://register.uke.com
To view, print, or download the latest manual supplement, visit
http://us.uke.com/usen/support/manuals.
Safety Information
A Warning identies conditions and procedures that are dangerous to the
user. A Caution identies conditions and procedures that can cause
damage to the Product or the equipment under test.
Warning
To prevent possible electrical shock, re, or personal
injury:
• Read all safety information before you use the
Product.
• Carefully read all instructions.
• Use the Product only as specified, or the protection
supplied by the Product can be compromised. Do not
touch voltages >30 V ac rms, 42 V ac peak, or 60 V dc.
• Comply with local and national safety codes. Use
personal protective equipment (approved rubber
gloves, face protection, and flame-resistant clothes)
to prevent shock and arc blast injury where
hazardous live conductors are exposed.
• Do not use the Product around explosive gas, vapor,
or in damp or wet environments.
• Limit operation to the specified measurement
category, voltage, or amperage ratings.
• Do not use test leads if they are damaged. Examine
the test leads for damaged insulation, exposed metal,
or if the wear indicator shows. Check test lead
continuity.
• Remove the test leads from the signal source before
you clean.
• Use only cables with correct voltage ratings.
• Keep ngers behind the nger guards on the probes.
• Do not exceed the Measurement Category (CAT)
rating of the lowest rated individual component of a
Product, probe, or accessory.
• Do not use the Product if it is damaged.
• Do not expose the Product to temperatures ≥
≥
≥
≥≥80°C
(176°F). H s cause igh temperature permanent damage
to the magnet.
• Make sure the magnetic force is strong enough to
keep the P Product in place. The roduct works only on
ferromagnetic material.
• In applications with low impedance between two
magnet probes, do not touch the metal parts of one
test lead when the other is connected to hazardous
voltage.
Symbols
The table below lists the symbols used on the Product and in this
instruction sheet.
Symbol Description
Risk of Danger. Important information. See Instruction
Sheet.
Conforms to European Union directives.
Certied by CSA Group to North American safety
standards.
Measurement Category III is applicable to test and
measuring circuits connected to the distribution part of
the building’s low-voltage MAINS installation.
Measurement Category IV is applicable to test and
measuring circuits connected at the source of the
building’s low-voltage MAINS installation.
This product complies with the WEEE Directive
marking requirements. The axed label indicates that
you must not discard this electrical/electronic product
in domestic household waste. Product Category: With
reference to the equipment types in the WEEE
Directive Annex I, this product is classed as category 9
"Monitoring and Control Instrumentation" product. Do
not dispose of this product as unsorted municipal
waste.
Produktspezifikationen
| Marke: | Fluke |
| Kategorie: | Nicht kategorisiert |
| Modell: | MP1 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Fluke MP1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Fluke
14 Juni 2025
11 Juni 2025
8 Oktober 2024
5 Oktober 2024
23 September 2024
21 September 2024
20 September 2024
10 September 2024
5 September 2024
Fluke IntelliTone Networks MT-8200-60-KIT Bedienungsanleitung
5 September 2024Bedienungsanleitung Nicht kategorisiert
- Aqara
- Unicol
- Consul
- Prowise
- Vivax
- Medeli
- Casio
- MantelMount
- Farberware
- Kelvinator
- Strex
- Salewa
- Clingo
- DMT
- B-Tech
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025