Forte Lighting 2738-03 Bedienungsanleitung

Lies die bedienungsanleitung für Forte Lighting 2738-03 (1 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 8 Bewertungen. Hast du eine Frage zu Forte Lighting 2738-03 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

ASSEMBLINGINSTALLATIONINSTRUCTIONS &

Thedrawingshownmaynotexactlymatchtheproductenclosed .

Howeverthe installation instructionsdo applytothisproduct, .

2738-03

WARNINGSHUT POWEROFFAT FUSE OR CIRCUIT BREAKER! .

ATTENTIONCOUPERLECOURANTAUFUSIBLEOUUNDISJONCTEUR! .

ASSEMBLINGTHEFIXTUREFig1 (.)

.

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

BlackHot()

FIXTURE

WIRES

Whiteor

Ribbed

FIXTURE

WIRES

Bare

Copper

()Ground

HOUSE

WIRES

White

()Neutral

HOUSE

WIRES

GreenorBare

CopperGround()

FIG.3

FIG.2

Junction box

( notincluded)

F

G

H

I

J

H

K

L

M

N

N

P

O

FIG.1

1.Shut off the power at the circuit breaker box. Remove old fixture and all hardware from

Junction Box. Carefully unpack your new fixture and lay out all the parts on a clear

area. Be careful not to lose any small parts necessary for installation.

2.Slide the electrical wires through the tube (I), and the housing (G). Turn the tube (I)

clockwise until tight.

3.Screw the housing (G) to the nipple on tube (I). Secure decorative bars (J) by screwing

decorative nuts (H) tightly.

HANG THE FIXTURE (Fig.2)

4.Determine the appropriate hanging height. There are a 6” (D), a 12” (E) and an 18” (F)

rod included in the package for height adjustment.

5.Slide the electrical wires through the tubes(D), (E), or (F), turn them clockwise until

tight.

6.Secure two mounting screws downward on the mounting plate by tightening the nuts.

Make sure the space between them is the same space between the holes on the

canopy (B). The side of the mounting plate that contained “GND” should be facing

down.

7.Secure the mounting plate to the junction box (not included) by aligning another two

mounting screws upward with the holes on the junction box. Tightening the screws with

a screw driver.

8.Have someone to support the weight of the light. Connect the electrical wires as shown

in . Make sure all wire nuts are securely twisted. You may wrap the connectionsFig. 3

with electrical tape. If your outlet does not have a copper (ground) wire, please wrap

the fixture's ground wire around the green screw (GND) on the mounting plate and

tighten the green screw.

9.Raise the canopy (B) to the junction box. Feed the two downward mounting screws

through the two holes on the canopy (B). Secure with decorative nuts (C).

10.Install light bulbs (not included) in accordance with the fixture's specifications.

NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!

ASSEMBLING THE REFLECTOR(Fig.1)

11.Install the nipple(L) on the coupler, and secure it using the hex nuts. Put the flat

washer(M),plastic washer(N) through the nipple. Raise the round glass reflector(O) to

the fabric shade, and secure it with the washer(N),bottom finial(P).

Your installation is now complete. Return power to the Junction box

and test the fixture.

Produktspezifikationen