Foscam FN3109H Bedienungsanleitung

Lies die bedienungsanleitung für Foscam FN3109H (8 Seiten) kostenlos online; sie gehört zur Kategorie Videorecorder. Dieses Handbuch wurde von 37 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 3 Bewertungen. Hast du eine Frage zu Foscam FN3109H oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

5467

1 23

Quick Installation Guide

Network Video Recorder

Model: FN3109H / FN3104H

V1.5.5

WARNING

Before installing a hard disk drive (HDD), please make sure the power

is disconnected from the NVR.

It is recommended that a hard drive be used in 7200 high-speed or

above.

Power cable

HDD

Data cable

It is recommended to use SATA type of hard disk for recording.

Note

1. Remove the cover from the NVR by unfastening the screws on the

rear and side.

2. Connect one end of the data cable and power cable to the

motherboard of NVR and the other end to the HDD.

3. Place the HDD on the bottom of the device and then fasten the

screws on the bottom to x the HDD.

4. Re-install the cover of the NVR and fasten screws.

Internet usersIP Camera

Power Switch

Power Supply

HD-OUT Video Output

VGA Video Output

USB Interfaces

DC 12V

POWER

HD-OUT VGALANUSB ALARM N1

1 2 3 4NOC

Alarm INAlarm OUT

Router

Internet users

Procedure

1. Connect your display to one of the video outputs (VGA or HD-OUT

interface).

2. Connect an external storage device to the USB interface of the NVR as

a backup.

3. Connect a mouse to the USB interface.

4. Connect an alarm input device to alarm input interface and connect

an alarm output device to alarm output interface respectively.

5. Some devices need to connect to your router using an Ethernet cable,

including the NVR, PC and IP Camera.

6. Connect the power adapter to the power input port.

Foscam cameras and NVRs require good security practices to

safeguard your privacy. You should regularly change your

camera or NVR password which is the combination of

numbers, letters and symbols.

You should update your camera or NVR regularly. Make sure

your camera or NVR has the latest rmware installed for your

specic model and better experience.

NVR

Screw Pack

DC Power Adapter

Ethernet Cable

Data Wire and Power Wire

of the Hard Drives

Quick Installation Guide

Warranty Card

USB Mouse

1. Turn on the power switch on the rear panel.

After the NVR starts up successfully, the power LED and HDD LED

indicators will turn green. The startup page is displayed on the screen.

2. Login page.

Select the Language, Enter the and , then click Username Password

on the button.Login

Default username is

admin with no password

Package Contents

Security Warning

1Before You Start2Hard Disk Installation

3. For the initial log in, the system will prompt you to change your

password. Once done, click the button. OK

4. After modifying the password, you will be taken to the Setup

Wizard.

1. Setting the time. If you don’t want to use the Setup Wizard next

time, uncheck the checkbox. Click the button.Setup WizardNext

2. Select the HDD you would like to use, then click the Format Hard

Disk button to set up the HDD. Note that this will delete all les on

the HDD.

Select a protocol depending on which IP Camera you have.

FOSCAM protocol: The High Denition (HD) IP Cameras for Foscam.

MJ protocol: The Standard Denition (SD) IP Cameras for Foscam.

ONVIF protocol: IP Cameras which support ONVIF protocol.

3. You can add an IP Camera that is connected to the internet on the

NVR.

You can congure the following information for your IP Camera.

The Setup Wizard can walk you through some important settings on

the NVR.

1. Select Your IP Camera

2. Click Add

3Device Connection45 Log InSetup Wizard

Input a new password,

then click OK.

Uncheck the checkbox

2. Click Format Hard Disk

3. Click Next

1. Select your HDD

Format Hard Disk

For detailed manuals, tools, etc., please visit foscam.com/downloads.

Produktspezifikationen