Frigidaire FARE1011MW Bedienungsanleitung

Lies die bedienungsanleitung für Frigidaire FARE1011MW (2 Seiten) kostenlos online; sie gehört zur Kategorie Wäschetrockner. Dieses Handbuch wurde von 46 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 23.5 Bewertungen. Hast du eine Frage zu Frigidaire FARE1011MW oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

DRYNESS LEVEL (IF EQUIPPED)

SELECTABLE IN AUTO DRY CYCLES ONLY

3 beeps =

dryer power up

2 beeps =

cycle pause

1 beep =

cycle start

STATUS

INDICATOR

BEEPS

Push in to start cycle.

Push in to pause cycle.

START/PAUSE

DRYER

Turn or push in to

power up dryer.

POWER UP

DRYER

NOTE TO

INSTALLER

Leave these instructions

with the customer.

REMARQUE POUR

L’INSTALLATEUR

Laissez ces instructions au

client.

Suite de la version française au verso.

NOTA AL

INSTALADOR

Deje estas instrucciones

con en cliente.

Español continua en la pagina trasera.

WARNING

• Dryer must be properly grounded at all times.

• Vent dryer through free-fl owing, outdoor-vented, metal duct system.

• Improper gas installation or LP conversion could result in injury or even death.

• Avoid back or other injury. Use more than one person to move, lift or tip the dryer.

IMPORTANT

Please read all safety instructions before using your

new dryer. For best drying results with your new

dryer, remember to review:

9

INSTALLATION INSTRUCTIONS

9

USE & CARE GUIDE

137542900A (1204)

IMPORTANT

For closet installations see detailed installation instructions

enclosed.

• USE ONLY 4 INCH (10.2 CM) RIGID METAL OR SEMI-

RIGID METAL DUCTING

• REPLACE PLASTIC OR FOIL DUCTS WITH METAL

• CLEAN LINT FROM PRESENT DUCT SYSTEM BEFORE

ADDING ON

• SEE CHART TO THE RIGHT FOR ACCEPTABLE NUMBER

OF 90° TURNS IN SYSTEM

• DO NOT USE SCREWS TO CONNECT DUCTS

• DO NOT USE REGULAR DUCT TAPE TO CONNECT DUCTS,

ONLY METAL FOIL TAPE

• 4" (10.2 cm) CLAMP RECOMMENDED FOR

CONNECTION BETWEEN DRYER & EXHAUST SYSTEM

• EXHAUST SYSTEM MUST BE VENTED OUTSIDE WITH

APPROVED VENT HOOD

• TO VENT LEFT OR RIGHT FROM DRYER, USE 90°

QUICK-TURN ELBOW

• FOR INSTALLATION IN A RECESSED AREA OR CLOSET,

SEE COMPLETE INSTALLATION INSTRUCTIONS

• FOR MOBILE HOME INSTALLATION, SEE COMPLETE

INSTALLATION INSTRUCTIONS

Number of 90° turns

MAXIMUM LENGTH*

of 4” (10.2cm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

4”

(10.2cm) louvered

2.5”

(6.35cm)

064 ft. (19.5 m)48 ft. (14.6 m)

152 ft. (15.9 m)40 ft. (12.2 m)

244 ft. (13.5 m)32 ft. (9.8 m)

336 ft. (11.0 m)24 ft. (7.3 m)

428 ft. (9.5 m)16 ft. (4.9 m)

*Do not install plastic or foil ducting. If installing semi-rigid

ducting, do not exceed 8 ft (2.4 m) total duct length.

INCORRECT

CORRECT

VENT EXHAUST

EMPTY DRUM

CONTENTS

CART FROM REAR

ONLY WITH 7" (MIN.)

CART FORKS

DO NOT CART

FROM FRONT

DO NOT USE KNEE

IN CABINET SIDE

TO MOVE UNIT

DO NOT CART

FROM SIDE

DO NOT USE OPEN

DOOR TO LIFT OR

TIP THE UNIT

DO NOT USE REAR CONSOLE TO PUSH,

PULL, TIP OR MOVE THE DRYER.

CAREFULLY

TIP

REMOVE & SAVE

PROTECT

FLOOR

RETURN

UPRIGHT

A)

B)

D)

UNPACKING & HANDLING

CONNECT

POWER

D)

CAUTION

ELECTRICAL SHOCK HAZARD

Do NOT use prong adapter.

Do NOT remove ground prong.

Do NOT use extension cord.

LEVEL BOTH WAYS

B)

CHECK STABILITY,

CORNER-TO-CORNER

C)

E)

OPEN GAS VALVE AND

CHECK FOR LEAKS

WITH SOAPY WATER

raise lower

ADJUST

A)

INSTALL

U.L.-APPROVED

STRAIN RELIEF

GAS DRYER

ELECTRIC DRYER

WRENCH-TIGHT

MANUAL SHUTOFF

L.P. SYSTEMS MUST USE

COVERSION KIT INSTALLED

BY QUALIFIED TECHNICIAN.

30 AMP

DON'T MOVE

30 AMP

MOVE GROUND

GREEN

RED OR

BLACK RED OR

BLACK

WHITE

APPLY APPROVED THREAD SEALANT.

REFER TO INSTALLATION

INSTRUCTIONS FOR MORE DETAILED

INFORMATION.

HEAT SOURCELEVEL & CONNECT

2-PERSON CARRYING

STRAPS, FRONT-TO-

BACK RECOMMENDED

C)

Damp Dry (on select models)

Low

Normal Dry

High

Max (on select models)

CLEAN LINT FILTER

AFTER EVERY LOAD.

THE EXHAUST SYSTEM SHOULD BE INSPECTED

AND CLEANED A MINIMUM OF EVERY 18 MONTHS

WITH NORMAL USAGE. THE MORE THE DRYER IS

USED, THE MORE OFTEN YOU SHOULD CHECK

THE EXHAUST SYSTEM AND VENT HOOD FOR

PROPER OPERATION.

OPERATE

Produktspezifikationen