Furrion C-FACR15SA-A04 Bedienungsanleitung

Lies die bedienungsanleitung für Furrion C-FACR15SA-A04 (6 Seiten) kostenlos online; sie gehört zur Kategorie Klimaanlage. Dieses Handbuch wurde von 27 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 14 Bewertungen. Hast du eine Frage zu Furrion C-FACR15SA-A04 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

HEAT STRIP INSTALLATION KIT

KIT D’INSTALLATION DE BANDE CHAUFFANTE

KIT DE INSTALACIÓN DE TIRAS DE CALE-

FACCIÓN

MODEL/MODÈLE/MODELO: C-FACR15SA-A04, C-FACR15HESA-A01

LIPPERT NO/LIPPERT NO./LIPPERT N.°: 2021123626, 2021132287

INSTALLATION GUIDE ....................................................EN

GUIDE D’INSTALLATION ...................................................................FR

GUÍA DE INSTALACIÓN ..................................................ES

* Product picture for reference only.

* Photo du produit pour référence uniquement.

* El producto de la imagen es solo de referencia.

This manual will guide you through proper installation of the Furrion heat strip. If

retrofitting, please refer to your existing user manual to uninstall the rooftop and trim

kit from the RV, and then follow the instructions to install the heat strip.

DANGER

Electric Shock Hazard

●Disconnect power or shut off the air conditioner circuit breaker

before installation.

●Failure to do so can result in electric shock.

WHAT’S IN THE BOX

●Heat Strip

●ST4 x 9mm Screw with Washer

●Electric Control Box

●User Manual

●Warranty Manual

INSTALL/REPLACING THE HEAT STRIP

IMPORTANT: Installation of the heat strip must be carried out by a professional/

certificated technician only.

Disassemble the Top Unit

Remove the rooftop cover by removing

the fixing screws. Pull to remove the

evaporator EPP cover to access the

evaporator. (Fig. 1)

Heat Strip Installation

Use 4 ST4*9mm screws and washers

(provided) to attach the heat strip on the

evaporator. (Fig. 2)

Fix the harnesses together with nylon

cable ties (not provided). Then pass the

2 harnesses down through the air intake

vent to the RV. (Fig. 3)

NOTE: Retain wire harnesses away from

the electric heater element and evaporator

to prevent being damaged.

Install the EPP top cover of the evaporator and the top cover back. Ensure the pipe

outlet is sealed well with the existing silicon sealant.

Evaporator

EPP Cover

Rooftop Cover

Fig. 1

Evaporator

Heat Strip

Heat strip wireRooftop unit wire

Fig. 2Fig. 3

WIRE CONNECTION

1. Remove the controller cover on the

control box by unscrewing its screw.

2. Loosen the 2 screws of the power cord

clamp on the back of the control box.

3. Pass the 115VAC power cord through

the cable clamp hole and make wire

connections following the below color

codes (Fig. 4):

– Black - Hot

– White - Neutral

– Green/Yellow - Ground

4. Plug the 3-pin connector of the rooftop

into the 3-pin terminal interface on the

control box. (Fig. 5)

5. When the heat strip is connected properly, secure the electrical box trim kit body.

(Fig. 6)

115VAC Power Cord

Heat Strip Cable

Fig. 5Fig. 6

The installation is completed.

Controller Cover

Cable Clamp

3

1

115VAC Power Cord

2

Fig. 4

SET UP

Set up the DIP Switches

Set up the control box dip switches as indicated in the illustration and table below.

ON

123 45 6

Zone Selection DIP 1 : DIP 2DIP 1DIP 2Selected

OFFOFF ZONE1

OFFON ZONE2

ONOFF ZONE3

ONON ZONE4

Heat Pump (selected models)DIP 3Reserved

FurnaceOFFDIP 4Furnace Off

ONFurnace On

Electric Heat (selected

models)

DIP 5Heat Strip OffOFF

ONHeat Strip On

Analog / DigitalDIP 6 OFFDigital

ON Analog

Switch DIP 5 to ON position to activate the heat strip function.

Refer to your Wall Thermostat for operation of your heat strip.

SPECIFICATION

Specifications

Heating Capacity1,500W

Applicable Ambient Temperature in cooling-7°C~30°C (19°F~86°F)

Volts/Hertz 115V~/60Hz/1Ph

Power Watts1,500W

Amps 14.6A

Power Cord Gauge AWG14 (1.6 mm2)

Dimensions (W x H x D)17⁄" x ⁄" x 3⅞" (452mm x 23.5mm x 98mm)

Weight (lbs/kg)1.63/0.74

Safety StandardCSA/UL 60335-1, Second Edition &

CSA/UL 60335-2-40, Second Edition

Produktspezifikationen