GE JX2027DMCC Bedienungsanleitung

Lies die bedienungsanleitung für GE JX2027DMCC (8 Seiten) kostenlos online; sie gehört zur Kategorie Mikrowelle. Dieses Handbuch wurde von 21 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 11 Bewertungen. Hast du eine Frage zu GE JX2027DMCC oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Built-In Trim Kits

Instructions JX2027 and JX2030

Read these instructions completely and carefully.

•IMPORTANT –Save these instructions for local inspector’s use.

•IMPORTANT –Observe all governing codes and ordinances.

•Note to Installer –Be sure to leave these instructions with the

Consumer.

•Note to Consumer – Keep these instructions for future reference.

•For easier installation and personal safety, we recommend that two people

install this microwave oven.

WARNING —This oven must be plugged into a properly

grounded 3-hole, 120V receptacle as required by the National Electrical Code

or the Canadian Electrical Code.

❒

BEFORE YOU BEGIN

• Do not alter or modify any part of this kit or the oven.

• Unplug the microwave oven before attempting installation of this kit.

• Skill level– Installation of this appliance requires basic mechanical and

electrical skills.

• Completion time– 1-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• This kit is UL/CSA listed for installation alone or over any GE/GE Profile

single electric wall oven. Not for use adjacent to (within 2 feet of) any gas

or electric range, cooktop or oven.

• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,

PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,

JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,

PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.

TOOLS YOU WILL NEED

❒ Phillips screwdriver

❒ Pencil

❒ Tape measure

❒ Awl or punch

❒ Drill with 7⁄64″bit or #35

FOR YOUR SAFETY:

WARNING –Before beginning the

installation, switch power off at service panel and lock

the service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the

service panel.

❒ Level

❒ Scissors (optional)

1

PART QUANTITY

❒ Trim Frame1

❒ Bottom Duct1

❒ Side Duct1

❒ 4 mm x 12 mm 23

Round-Head Screws(21 required

for installation)

❒ 4 mm x 14 mm 6

Flat-Head Screws

(4 required for

installation)

❒ Anti-Tip Brace 1

❒ Anti-Tip Bracket 1

❒ Upper Duct 1

❒ Top Bracket1

❒ Bottom Bracket1

❒ Templates 2

PARTS INCLUDED

NOTE: This kit has extra screws to prevent the technician from spending extra

time locating a replacement screw in case they lose one during installation.

Questions? In the U.S., call 800.GE.CARES (800.432.2737) orVisit our Website at:ge.com.

In Canada, call 1.800.561.3344 or Visit our Website at:GEAppliances.ca.

Produktspezifikationen