GE JXS77WW Bedienungsanleitung
Seiten 2 Engels Ofen
Lies die Bedienungsanleitung für GE JXS77WW kostenlos online oder lade das PDF herunter. 47 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
Installation Instructions
Body Side Kit For End of the Counter Installation
Tools Required:
#2 Phillips screw driver
Installing the Kit
This Body Side Kit must be installed prior to installing the Range in position.
Locate the body side keyway holes over the heads of the panel supports.
A
A1 Place the three panel supports in the 3 square holes of the vertical side trim and rotate 45° as shown below.
( May require Pliers) See illustration on back page.
A3 Insert 1” screw through shoulder rivet. Place the 1/2” spacer over the end of the 1” screw. Place the spacer-
shoulder rivet-screw assembly through washer. Install assembly in place of the screw removed in A2. (See
illustration on back page.)
A4
Pub. No. 31-10451
229C4053P434
Push the body side forward locking the slots of the keyway holes on the side panel supports.
A5
Place the longest screw (1-1/2” ) through the top hole of the body side at the rear of the range. Slide the spacer
(1-1/4”) over the screw and attach the screw to the hole in the rear of the range above the louvers. Do not tighten.(If
a backsplash kit is used in conjunction with this kit, use the shorter spacer found in the backsplash kit.) See
illustration on back page.
A6
Lift the rear of the body side to close the gap between the cooktop glass and the body side. Tighten the screws
from steps A6 and A7.
A7
Place the short (3/8” long) hex head screw through the bottom hole in the rear of the body side and attach to the
lower section of the range. See illustration on back page, Do Not Tighten.
A8
To stabilize the bottom front corner of the body side-range assembly, place the clip over the inside flange of the
body side and the outside flange of the vertical side trim, as shown in illustration. Start by raising the front corner
of the range by turning the leveling leg downward, to provide more clearance for attaching clip. See illustration on
back page for details of attaching clip. (Hold the body side and the vertical side trim close for easier assembly
of the clip.) See Illustration on back page.
A9
Refer to the Installation Instructions included with the range to place the range into kitchen location.
A10
1/4” Nut Driver
Pliers
Parts Supplied:
3 Panel Supports
1 Body Side
1/2” Spacer
1-1/4” Spacer
Clip
Shoulder Rivet
Washer
#8-3/8” Long
Hex Screw
#8-1” Long Screw
#8-1-1/2” Long Screw
Use these instructions to mount the Body Side Kit on either side of the Slide-In Range.
Remove the hex head screw at the top end of the vertical side trim as shown in the illustration on back page.
A2
1
Produktspezifikationen
| Marke: | GE |
| Kategorie: | Ofen |
| Modell: | JXS77WW |
Brauchst du Hilfe?
Wenn Sie Hilfe mit GE JXS77WW benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Ofen GE
GE JXFILLR1DD Bedienungsanleitung GE EGR3000ELBB Bedienungsanleitung GE JXS37WW Bedienungsanleitung GE JGP328BEKBB Bedienungsanleitung GE JXHC1 Bedienungsanleitung GE Profile PGS975SEPSS Bedienungsanleitung GE Profile JMP31WAWW Bedienungsanleitung GE JGP626AEVAA Bedienungsanleitung
Alle GE Ofen Bedienungsanleitungen
Beliebt in Ofen
GE Profile J2S968TEKWW Bedienungsanleitung GE JMS08BA2AD Fornuis Bedienungsanleitung GE Profile PB900SPSS Bedienungsanleitung
Bedienungsanleitung Ofen
Neueste Bedienungsanleitungen für Ofen
Uniprodo UNI_FP_10 Bedienungsanleitung Uniprodo UNI_FP_11 Bedienungsanleitung Oranier Hektos Aqua II Bedienungsanleitung Flama 2331FL Bedienungsanleitung Oranier Pori Aqua Bedienungsanleitung Flama 2336FL Bedienungsanleitung Flama 2319FL Bedienungsanleitung Flama 2391FL Bedienungsanleitung Flama 2327FL Bedienungsanleitung Flama 2387FL Bedienungsanleitung