Gigabyte GA-H270M-D3H Bedienungsanleitung
Gigabyte
Hauptplatine
GA-H270M-D3H
Lies die bedienungsanleitung für Gigabyte GA-H270M-D3H (18 Seiten) kostenlos online; sie gehört zur Kategorie Hauptplatine. Dieses Handbuch wurde von 13 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 7 Bewertungen. Hast du eine Frage zu Gigabyte GA-H270M-D3H oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/18
- 1 -
Table of Contents
Conguring a RAID Set (Intel® Z270/H270 Series) .........................................................2
1-1 Conguring SATA Controllers ............................................................................. 2
1-2 Installing the SATA RAID/AHCI Driver and Operating System.......................... 16
- 2 -
Conguring a RAID Set (Intel® Z270/H270 Series)
To create a RAID set, follow the steps below:
A. Install SATA hard drive(s) in your computer.
B. Congure SATA controller mode in BIOS Setup.
C. Congure a RAID array in RAID BIOS. (Note 1)
D. Install the SATA RAID/AHCI driver and operating system.
Before you begin, please prepare the following items:
•At least two SATA hard drives or SSDs (Note 2) (to ensure optimal performance, it is recommended that you
use two hard drives with identical model and capacity). (Note 3)
•A Windows setup disk.
•Motherboard driver disk.
•A USB thumb drive.
RAID Levels
1-1 Conguring SATA Controllers
A. Installing hard drives
Install the hard drives/SSDs in the Intel® Chipset controlled connectors on the motherboard. Then connect
the power connectors from your power supply to the hard drives.
RAID RAID RAID RAID 0 1 5 10
Minimum
Number of Hard
Drives
≥2 ≥32 4
Array Capacity Number of hard
drives * Size of the
smallest drive
Size of the smallest
drive
(Number of hard
drives -1) * Size of
the smallest drive
(Number of hard
drives/2) * Size of the
smallest drive
Fault Tolerance No Yes Yes Yes
(Note 1) Skip this step if you do not want to create RAID array on the SATA controller.
(Note 2) An M.2 PCIe SSD or an U.2 SSD cannot be used to set up a RAID set either with an M.2 SATA SSD
or a SATA hard drive.
(Note 3) Refer to Chapter 1, "Internal Connectors," for the installation notices for the U.2, M.2, and SATA
connectors.
- 3 -
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
B. Conguring SATA controller mode in BIOS Setup
Make sure to congure the SATA controller mode correctly in system BIOS Setup.
Step 1:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Go to
Peripherals\SATA And RST Conguration SATA Controller(s), make sure is enabled. To create RAID, set
SATA Mode Selection Intel RST Premium With Intel Optane System Acceleration to (Figure 1).
Step 2:
To use the EZ RAID feature, follow the steps in "C-1." To congure UEFI RAID, follow the steps in "C-2." To
enter the legacy RAID ROM, refer to "C-3" for more information. Finally, save the settings and exit BIOS Setup.
Figure 1
Produktspezifikationen
| Marke: | Gigabyte |
| Kategorie: | Hauptplatine |
| Modell: | GA-H270M-D3H |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Gigabyte GA-H270M-D3H benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Hauptplatine Gigabyte
7 Oktober 2024
5 Oktober 2024
24 September 2024
17 September 2024
16 September 2024
15 September 2024
13 September 2024
11 September 2024
10 September 2024
9 September 2024
Bedienungsanleitung Hauptplatine
- Asus
- Sharkoon
- MSI
- AVerMedia
- Supermicro
- NZXT
- Asrock
- ECS
- EPoX
- Evga
- Intel
- Abit
- Elitegroup
- Foxconn
- Biostar
Neueste Bedienungsanleitung für -Kategorien-
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025