Godox TT520 II Bedienungsanleitung

Lies die bedienungsanleitung für Godox TT520 II (1 Seiten) kostenlos online; sie gehört zur Kategorie Blitz. Dieses Handbuch wurde von 50 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 25.5 Bewertungen. Hast du eine Frage zu Godox TT520 II oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

The flash unit has 8 steps of poweroutput controlwhich indicatedby 8

pieces of LED lamp for different level.

Press the MODE key to M Mode. In this mode ,you can set TT520 II

/TT560 II onto your camerahotshoeorspeedlite triggerhotshoe to trigger

the flash unit. When shooting, adjust the flash powerandpress the

camera shutter, the flash light will flash under the camera synchronous

signal.

Press the MODE key to S1 Mode. Themode is applicable for slave flash

inorder to create many lighting effects. It is respectively applicable for

manual flash environment.

Press the MODE key to S2 Mode. Themode is applicable for slave flash

inorder to create many lighting effects.The flash unit won’t flash synchro-

nously with the first flash but the second flash from themaster flash,

which is the second flash synchronization.

WARNING

Thank you forpurchasing GODOX product.

Beforeuse, pleaseread this usermanual carefullyinorder to ensure

your safety. Keep it properly forreferencein future.

FOREWORD

Always keep this product fromrainordampinorder to prevent

fireor electricshock.

The flashunit contains highvoltageelectric parts, donot try to

openorrepair the flash unit. If you touch the high-voltage circuit

inside thisproduct, electric shock may occur. Return it back to

thenominatedrepair service station.

If theunit is extruded,fallen,suffered from strongimpact and thus its

insideis exposed, stop usingimmediately so as to prevent electric

shock leading from touching theinsideelectric components.

Donot fire the flash direct to the eye at short distance(especiallybaby’s

eye), or it maydamage the eye.When taking flash picture towardbaby,

it is recommended to keep the flash unit at least 1 meter(3.3feet) away

from the subject. Or use diffuseror bounce thelight to soften its intensity.

Always keep thebattery oranythingeasy to begulpedout of children's

reach. In case of gulping due to carelessness,please contact a doctor

immediately .

When there is caustic liquidleakageinside, it is necessary to wear

gloves to takeout thebatter.

Donot use the flash unit in the flammablegas, chemicalorsuch liquids.

These materials may beensitive to the flash from theunit in some circ-

umstance. It may cause fireor electromagnetic interference.

Please pay attention to thewarningmarks in theshooting surroundings.

Donot leave or store the flash unit in temperature over 40C(such like

in theautomobile), orit may damage the electronic components.

The flash unit isn’t waterresistant.

Please keep it away from rain or humidity.

If the flash unit isidle forlong, please take out allbatteriesand keep

the flash unit indry area.

Open the batterycover

Slide thebattery cover

along thearrow

directionand thenopen

it by thumb.

Insert batteries

Install thebatteries

according to thedirection

indicated by the sickerin

thebattery holder and

make sure the + and–

battery contact are

correctly insertedat the

battery compartment.

Closethe batterycover

Slide thebattery cover

along thearrowdirection

and slide it back inplace.

Thebattery cover will be

lockedwhen there is a

“click” sound.

Take out the battery when idle in case the battery leakage damages the

flash unit.

Attention:

Twist thelock ring anti-

clockwise to loosen it to the

highest point. Slide the

mounting foot of the flash

into thehotshoeof camera.

Twist thelock ring

clockwise to tighten it.

To remove the flash,

loosen the fixed knoband

slide it out of thehotshoe

of camera.

Mini Stand

Built-in Wide Panel Reflection Board

Optic Control Sensor

Flash Head

Hot Shoe Stand

Lock Ring

Dedicated Hot Shoe Contact

Switch to the ON, the flash will start charging(the charging indicator is

dim).After several seconds, the chargingindicator turns redand

TT520 II /TT560 II is ready to shoot.

For a test flash, press the test button. Afteruse, press the ON/OFF to OFF to

power off.

If thered chargingindicatorlamp flickers in every 1s, it indicates low

battery. In such case, the power will turn off automaticallyand you

need to replace thebatteries.

Note：

Theoptic light sensorwill stop functioningunder M Mode.

Thehotshoe’s trigger function will stop under S1 and S2 Mode.

To save battery power, the flash will enter stand-by state inabout 30

minutes of idle use. Press any button to wake it up.

In S1/S2 mode, the flash willenter stand-by state in about 60 minutes

of idle use. Press any button to wake it up.

In power-savingmode, the charging indicator flickers in every 3 seconds.

Otherindicators are turned off.

Number of flashes that will activate over-temperature protection:

1.Bounce Lighting

Bounce flash means to take photos by bouncing thelight off wallor

ceiling to soften thelight on the subject, and the shadow shadeout,

to get more desiredpicture.

2.UseReflection Board to Take Photos

Pullout the refectionboardandbuilt-inwidepanel from the flash head

at the same timeand thenpush thebuilt-inwidepanelback.

In such case, if this product is being used to take photos, it willproduce

a highlighted point on the eyes of thesubject and thus make theeyes

charming (catch lights). This function canreach optimaleffect when

the flash head is up90°.

3.Use Wide-angle Diffuser

Pullout the built-inwidepanel to enlarge flash lightingrange, so as to

get more softenedandnaturallighting effect.

Systematic over-temperature protection

2.Mounting the flash on the camera

Ⅲ. USING THE FLASH

1. Power management

5.S2 Mode

2.Power Control

3.M Mode

4.S1 Mode

Ⅳ. ADVANCED APPLICATION

Ⅴ. SPECIFICATIONS

Ⅱ. INSTALLATION

1. Battery Installation

8.Power-saving Function

Ⅰ. NOMENCLATURE

After use, press the ON/OFF to OFF to power off.

33 ( m ISO 100)38 ( m ISO 100 )

TT520 IITT560 II

Recycle time

100-1500 times (AA alkalinebatteries used)

4xAAsicebatteries(AlkalineorNi-MHare usable)

0~270degrees

0~90degrees

M,S1,S2

5600K+200K

1/300s~1/20000s

190*75*55mm

310g

Lighting times

approx 0.1-5s(AA alkalinebatteries used)

Color temperature

Flash duration

Dimensions

Net weight

Guidenumber

Model

Flash mode

Verticalrotationangle

Horizontalrotationangle

Power

Press “+” to make powerhigherand they are1/128,1/64,1/32,1/16,

1/8,1/4,1/2,1/1. Otherwise, press “-” to make power lower.

Accessories：

Flash light ......1 Protectingbag ......1Mini stand ......1

Usermanual...1RT transmitter…… 1

。

Power Switch

Test Button

Flash Power Level Button

Output Level

Indicator

Mode Select Indicator

（M、S1、S2）

Charging Indicator

Battery Cover

Mode Select Button

Takecare of the hot battery when changing them after continuous flashes.

When the flash is S1 mode, it will fire synchronously when themaster

flash fires, comparablewith the effect by the use of radio trigger.

Protection in continuous flashes

9.Protection Function

To prevent the flash head fromgetting toohot anddamage, pleasedo

not flash over20 times wheninpowerlevel 1/2,1/1. Please cooldown

the flash unit for at least 10minutes. The over-temperatureprotection

functionwill be activatedif you continue to flash after20 times. In this

state the charging timewill turn to 10-25s. Please cool down the flash

unit around10minutes and it will turn to normal state.

When theinner circuit is over-heating, which indicates overuseof the

flash unit, the inner circuit will shut downpowerautomatically. The flash

unit will turn to normal state after theinner circuit is cooleddown.

-

Socket Cover

Charging Socket

Sync Cord Jack

6.Wireless Triggering Function

Channel

Wireless Indicator

As TT520 II/TT560 II has built-inwireless signal, please use RT transmitter

as the transmitterend.

Longpress MODE button for2 seconds to control the ON/OFF of wireless

triggering function. When thewireless indicatorlighted, wireless triggering

functionis ON; when thewireless indicatorput out, wireless triggering function

is OFF. To save power, turn off wireless triggering functionwheninidleuse.

The speedlite and camerawill trigger synchronously by usinga PC sync

cord to connect the sync terminals of the cameraand the speedlite together.

7.Sync Trigger Function

PowerLevel

1/1

1/2

1/4

1/8

1/16,1/32

1/64，1/128

Number

20

33

50

66

100

200

Wireless frequency

Channel

Workabledistance

433MHz

16

15m

Produktspezifikationen