GPX TM35B= Bedienungsanleitung

Lies die bedienungsanleitung für GPX TM35B= (4 Seiten) kostenlos online; sie gehört zur Kategorie Flachbildschirmunterstützung. Dieses Handbuch wurde von 34 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 7 Bewertungen. Hast du eine Frage zu GPX TM35B= oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

TilTing FlaT Panel TV MounT For 40-65” TeleVisions

User’s Guide for Model No. TM35 v1381-01

STEP 1

Horizontal Base Plate

•AssembledHorizontalBasePlate.

NotemountingpointswhichwillbeusedforStep2.

Front Towards TV

Rear Towards Wall

Wall Mounting Points

•Concrete/Brickwallshown.Drillsixholesforsolidwallapplication.

•Usea3/8”or10mmdrillbit.

•Cutawayofdrywallwithstudsshownbehind.Drillfourholesforstud

application.UseastudndertolocateandONLY DRILL INTO STUDS!!

•Usea5/32”drillbit.

STEP 2

Pre-drill Holes for Base Plate

•DrillholesfortheBasePlatetoattachtothewall,usingexact

measurementsbasedonwhereyouwanttomounttheHorizontalBase

Plate.Onlydrillintoasolidwall,orstuds(behinddrywall).DO NOT

DRILL AND HANG THE BASE PLATE ON DRYWALL OR SHEETROCK.

ItisnotstrongenoughtosupportaTVandwillcausedamage.

WARNINGS

•ThewallmountedpartsoftheTVmountmustbermlyattachedtoa

concrete/brick/solidwoodwall,orwallstudsbehinddrywall.

•Tightenscrewssothatthewallplateisrmlyattached,butdonot

overtighten.Overtighteningcandamagethescrewsandincreasethe

chancesoffailure.

•Donotremoveorloosenanyscrewsuntiltheyarenolongerengaged

withthemount.Doingsomaycausethescreentofall.

•Itishighlyrecommendedtohavethismountprofessionallyinstalled.

•Supports VESA up to 600 x 400mm.

•This mount is designed to hold a maximum of 132 lbs (60 kg).

TOOLS

Thefollowingtoolsarerecommendedforthisinstallation:

•Drill

•5/32”drillbitfordrywall

•3/8”or10mmdrillbitforconcrete

•Studnder

•Phillipsscrewdriver

PARTS

x1H

x2M

Ax4

M8x15

x4B

M6x15

x4C

M5x15

x2O

M6x38

Lx6

Ø10x50

x6K

M6x50

x2I

M6x10

x1J

Mag Level

x4D

Ø5

x4E

Ø6

x4F

Ø8

Ø15xØ8x4.5

x4G

x2N

M6x15

Horizontal Base Plate x1

x1H

x2M

Ax4

M8x15

x4B

M6x15

x4C

M5x15

x2O

M6x38

Lx6

Ø10x50

x6K

M6x50

x2I

M6x10

x1J

Mag Level

x4D

Ø5

x4E

Ø6

x4F

Ø8

Ø15xØ8x4.5

x4G

x2N

M6x15

Horizontal Base Plate x1

x1H

x2M

Ax4

M8x15

x4B

M6x15

x4C

M5x15

x2O

M6x38

Lx6

Ø10x50

x6K

M6x50

x2I

M6x10

x1J

Mag Level

x4D

Ø5

x4E

Ø6

x4F

Ø8

Ø15xØ8x4.5

x4G

x2N

M6x15

Horizontal Base Plate x1

x1H

x2M

Ax4

M8x15

x4B

M6x15

x4C

M5x15

x2O

M6x38

Lx6

Ø10x50

x6K

M6x50

x2I

M6x10

x1J

Mag Level

x4D

Ø5

x4E

Ø6

x4F

Ø8

Ø15xØ8x4.5

x4G

x2N

M6x15

Horizontal Base Plate x1

x1H

x2M

Ax4

M8x15

x4B

M6x15

x4C

M5x15

x2O

M6x38

Lx6

Ø10x50

x6K

M6x50

x2I

M6x10

x1J

Mag Level

x4D

Ø5

x4E

Ø6

x4F

Ø8

Ø15xØ8x4.5

x4G

x2N

M6x15

Horizontal Base Plate x1

•Thehorizontalbaseplateisalreadypartiallyassembledfromthefactory.

Screwtheremainingverticalbarintothecentersectionofthebaseplate

asshown.Noteorientationofparts.

Note: Parts A-G are used to attach

your TV to the brackets in Step 4,

but you will not need all of them.

Find and use the set that best ts

your specic TV.

H

I

Produktspezifikationen