GW Instek GCM-407 Bedienungsanleitung

Lies die bedienungsanleitung für GW Instek GCM-407 (2 Seiten) kostenlos online; sie gehört zur Kategorie Messung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 8 Bewertungen. Hast du eine Frage zu GW Instek GCM-407 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Warning: Be sure to turn off circuit power and

discharge residual charge from all capacitors

before connecting a load.

to “ ”.

and auto-ranging mode.

Press REL to access

the relative mode.

results separate the resistive

element from the circuit. After

all measurement operations,

disconnect the probe and the

measured circuit and then

remove the probe from input end.

Warning: Be sure to turn off circuit power and

discharge residual charge from all capacitors

before connecting a load.

measurement function dial to

“ ”.

separate the diode from the

circuit.

operations, disconnect the probe

from the measured circuit then remove the probe

from the clamp inputs.

Warning: Be sure to turn off circuit power and

discharge residual charge from all capacitors

before connecting the load.

measurement function dial to

“ ”.

measured resistance is less

measured resistance exceeds

disconnect the probe from the measured circuit

then remove the probe from the clamp inputs.

Warning: Be sure to turn off circuit power and

discharge residual charge from all capacitors

before connecting the load.

measurement function dial to

“ ”.

Measurement notice:

measurement.

measuring large capacitances.

probe from the measured circuit then remove the

probe from the clamp inputs.

operations, disconnect the

probe from the

measured circuit then

remove the probe from

the clamp inputs.

and return to the common measurement state.

2.REL

to exit the mode.

power and discharge all capacitors before

measuring resistors, diodes or circuits.

circuit, then remove the probes from clamp

measurement.

been used for a long time.

9. Please do not alter the internal wiring of the

environment with high-temperature,

current magnetic fields.

use abrasives or solvents to avoid case

the range to the current measurement range.

auto-range function.

or off the REL function with these functions, first

short the test leads or connect the test leads to a

Note: Automatic shutdown function will be

up the meter from the sleep mode.

not used within 15 minutes during measurement.

-

ment function dial under automatic shutdown

operations.)

the unit from the sleep mode.

issue a long beep before power off.

indicated below, the corresponding functions or to

VIII. Measurement Instructions

to “ ”.

mode. Press REL to

access the relative

mode.

from the measured circuit then

remove the probe from the

clamp inputs after all measurement

operations.

to “ ”.

to auto-ranging. Press REL

to access relative mode.

from the measured circuit then

remove the probe from the

clamp inputs after all

measurement operations.

I.

IV

e nsulated

A

de

Warning prompt

A or

o meet European n standard.

Grounding

Low batterndication

Buing ON

3

4

69

10

12

11

5

8

14

1

2

15

7

13

igure 2

1 pc

1 pair

1 pc

1.

2. est Probes

. emperature probe

Operating Manual

meter with stable performance and a high degree of

are missing or damaged.

item is missing or damaged.

A Warning identifies conditions and actions that

attention to warnings and use the meter as

1. Please inspect the clamp meter and test leads

before use to avoid damage or abnormal use.

Please do not use the clamp meter again if the

test leads or case insulation is damaged, the

connectors, exosed inputs or circuits during

measurement.

change ranges during measurement to avoid

damaging the clamp meter.

meter terminal and ground to avoid electric

greater than the allowable input levels. Be sure

to set the function range switch to the highest

range possible if the magnitude of the measured

e

H

ELE

NANA

NA

RELHOL

V

igure

V

~

~

igure 4

function icons are selected after

trigger to open the clamp head.

current and converts the current to voltage. A

single conductor of the measured current must

head.

igure 1

Hz

1

2

5

7

6

4

3

Produktspezifikationen