Hager JKD11111 Bedienungsanleitung

Lies die bedienungsanleitung für Hager JKD11111 (3 Seiten) kostenlos online; sie gehört zur Kategorie Multimeter. Dieses Handbuch wurde von 30 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 15.5 Bewertungen. Hast du eine Frage zu Hager JKD11111 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

JKA Boards

Instructions/Data Sheet

This DBO and Hager devices conform with the following standards:

Meter Direct Fed EN 50470

BS EN 61439-3 including Annex ZB.

Switch-disconnectors: BS EN 60947-3.

Residual Current Circuit Breaker (RCCB): BS EN 61008-1

Residual current operated circuit breaker with integral overload (RCBO): BS EN 61009-1

Miniature Circuit Breaker (MCB): BS EN 60898-1

Installation Instructions:

All product(s) must be installed by a suitably competent electrician

Giving consideration to their intended use and in accordance with

the current edition of BS 7671 (IET Wiring Regulations).

The Electricity at Work regulations and the Health and Safety at Work

Act shall be complied with.

Only equipment and arrangements specied in Hager’s technical

documentation / catalogue shall be used.

Install in the horizontal plane only.

Important notice:

To prevent potential overheating from loose connections the installer

shall check connections are tight to the torque levels stated in these

instructions prior to energizing this board. This check should include

factory made connections which may have loosened in transit.

Tightening torque values to be applied (Nm)

Switch-disconnector’s: 40A & 63A: 2.8 Nm

Switch-disconnector’s: 100A: 3.6 Nm

RCCB’s 40A & 63A: 2.8 Nm

RCCB’s 80A & 100A: 3.3 Nm

MCBs: 2.8 Nm

RCBO’s: 2.8 Nm

Earth & Neutral terminal bar connections: 2.0 Nm

Single conductors below 1.5mm² need to be doubled back in the

terminal bar

Front metal cover xing screws: 2.0 Nm

Meter torque: 2.4 Nm

Good workmanship and proper materials must be applied by the

installer. The cable entry method shall, as far as reasonably practical,

maintain the non-combustable arrangement of the enclosure.

Account shall be taken of these instructions.

Metalclad units are provided with knockouts for standard 20, 25,

and 32mm conduit and large rear knockouts.

Pull and lift the terminal bar support away from the unit resting

the rail supported by the earth strap. After xing conduit/ cable

glands, locate the rail support and press down.

Note: Only BASEC approved cable should be used

1.0mm2 to 16mm2 for outgoing cables

up to 35.0mm2 for incoming live cables

Single conductors below 1.5mm² need to be doubled back in the terminal bar.

Cable entry facilities:Metal Unit - Removing and replacing the terminal rail for

cabling:

ZD0651 - Issue 4 03-15 - Issue 4 03-15ZD0651

JKA Boards

Instructions Sheet

JKA Boards

Instructions Sheet

ZD0651

ZD0651

ZD0651

ZD0651

4 1

GB

MCB

tripped

Use circuit as

normal

Use circuit as

normal

Unplug faulty

appliance until

repaired. Reset device.

Other appliances may

be used

Try & reset device once

Try & reset device once

Turn

OFF

all MCBs devices

Reset RCCB

Turn ON MCBs

devices one at a time

until RCCB trips again,

identifying faulty circuit

Unplug all

appliances from

circuit and reset

device / replace fuse*

Plug in & switch on

appliances one at a time

until device trips / blows,

identifying faulty appliance

What device

is it?

Does device

stay ON?

Does device

stay ON?

Does device

stay ON?

Does device

supply socket

outlets

Does device

stay ON?

STA R T

YES

YES

YES

YES

YES

MCB

or

RCB ORCC B

N O

N O

N O

N O

N O

T

T

T

ON ON ON

Blank RCCB RCBO (two module) MCB RCBO Switch

(one module)

Painted Metal Enclosure

Dimensions

(mm)

Enclosure Size

81216222x12 2x16 2x22 3x22

A254 326 398 505 326 398 505 505

B236 236 236 236 472 472 472 708

CN/A N/A N/A N/A N/A N/A N/A N/A

D125 125 125 125 125 125 125 125

AD

B

Produktspezifikationen