Hikvision DS-PDSK-P Bedienungsanleitung

Lies die bedienungsanleitung für Hikvision DS-PDSK-P (2 Seiten) kostenlos online; sie gehört zur Kategorie Alarmanlage. Dieses Handbuch wurde von 55 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 28 Bewertungen. Hast du eine Frage zu Hikvision DS-PDSK-P oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Specificaon

H2

H1

H3

H4

H5

H1 - Pulse Count

H2 - Pulse Count

H3 - LED

H4 - Sensivity

H5 - Latch

3.2

3.3

3.4

3.5

MaterialConcreteWoodFixed Window Frame

1.0m2.5m2.5m

H1

H2

H3

H4

H5

H1

H2

H3

H4

H5

Remove the jumper from the H5 (or put on just one pin so that the jumper is

not lost) to acvate the latching feature. If this feature is acvated and the

sensor is triggered, the LED on the sensor will stay on in order to display that it

has been acvated. To reset, the power must be removed from the device.

If the sensor detects “gross aack” (a vibraon higher than the calibrated sensivity), it will

override the pulse count and go directly into alarm.

108mm

30mm

22mm

37.5g

3.2 Sengs - Pluse Count

3.4 Sengs - Sensivity3.5 Sengs - Latch4 Wiring

Dimension

3.3 Sengs - LED

2 Installaon1 Component

3.1 Sengs - Jumper

Note: The stated values are typical. It is advised that

practical testing is performed before installation to verify

the operation. In some environments, these values may

differ from stated.

H1

H2

H3

H4

H5

Each me the pulse count seng is changed, the LED will flash the appropriate number of mes

to indicate which seng is selected. It will verify this by indicang the pulse count seng 3

mes, pausing between each verificaon.

a. Screw Cover

d. Light Pipe

e. PCB

b. Screw

f. Rear Panel

Wired Shock Detector

0s

0s

0s

0s

0.5s

0.5s

0.5s

0.5s

1s

1s

1s

1s

1.5s

1.5s

1.5s

1.5s

2s

2s

2s

2s

a. Powering up

b. Vibraon detected

c. Device triggered

d. Gross acvaon

Flash on and off

Flash once

Flash once → Off

Flash once → Latch (Remove H5)

Flash once → Off

Flash once → Stay on (Remove H5)

LED

a. High Sensivityb. Low Sensivity c. Increased. Decrease

Material and Mounng Posion

H1

H2

H3

H4

H5

Pluse Count

H1 H2 Pluse

1

2

4

6

a. Alarm Control Panel

b. Sensor

(1) Normally Closed

ZONE2

COM

ZONE1

COM

+

-

TAMPERALARM

-+

(2) Double End of Line Wiring

a. Alarm Control Panel

b. Sensor

Wiring Example:

1. Normal: 2.2 K

2. Alarm: 4.4 k

3. Tamper: Infinite

ZONE2

COM

ZONE1

COM

+

-

TAMPERALARM

-+

1

3

4

2

UD21449B

c. Front Panel

2.2K2.2K

SensorPiezoelectric sensor

SensivityPotenometer Adjustment

Tamper switchSupport

Intelligent algorithmSupport

Alarm outputNormally closed

LEDBlue (alarm)

Nominal voltage9 to 16 VDC

Nominal current30 mA

Storage temperature-20 °C to 60 °C (-4 °F to 140 °F)

Operang temperature-10 °C to 55 °C (14 °F to 131 °F)

Operang humidity10% to 90%

InstallaonWall-mounng

Dimension108 mm × 30 mm × 22 mm

Weight37.5g

FCC statements: This device complies with part 15 of the FCC Rules.Operaon is subject to the following

two condions:(1)this device may not cause harmful interface,and (2)this device must accept any

interference received,including interference that may cause undesired operaon

FCC Informaon

Please take aenon that changes or modificaon not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a

residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no

guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to

radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separaon between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC Condions

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operaon.

Produktspezifikationen