Hobart 4822 Bedienungsanleitung
Hobart
Fleischwolf
4822
Lies die bedienungsanleitung für Hobart 4822 (12 Seiten) kostenlos online; sie gehört zur Kategorie Fleischwolf. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 9 Bewertungen. Hast du eine Frage zu Hobart 4822 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/12
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
937 332-3000
www.hobar tcorp.com F-35109 Rev. A (April 2014)
MODEL 4822 CHOPPER
ML-136125
ML-136126
– 2 –
© HOBART, 2014
Installation, Operation and Care of
MODEL 4822 CHOPPER
SAVE THESE INSTRUCTIONS
GENERAL
The 4822 Chopper uses a 11/2 horsepower motor. It will grind 16 lbs. per minute, fi rst cutting, through a
1/ " plate.8
The 4822 Chopper, with funnel-shaped cylinder, will grind 20 to 22 lbs. per minute, fi rst cutting, through
a 1/ " plate.8
Fig. 1
– 3 –
INSTALLATION
UNPACKING
Remove the carton from around the machine. Remove the four bolts holding the machine to the skid.
Unpack the chopper cylinder assembly.
Immediately after unpacking the chopper, check for possible shipping damage. If this machine is found to
be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to make sure that it agrees with the specifi cations on the
machine data plate.
The four leg assemblies (Fig. 1) are removed and packed in a separate carton for shipment. Unpack and
assemble these legs by screwing them into the four tapped holes of the frame. The rubber feet on these
legs cushion the machine. Under normal operation, the machine need not be bolted down.
ELECTRICAL CONNECTIONS
The electrical cord on this machine is equipped with a grounding- type plug which
must be connected to a properly grounded receptacle. If the receptacle is not the proper grounding
type, contact an electrician. Do not remove the grounding prong from the plug.
Choppers with three phase motors should be connected so that the hub drive runs counterclockwise
facing the cylinder assembly.
A check must be made to verify correct direction of rotation. Energize machine momentarily by turning
switch ON then OFF.
If rotation is incorrect, disconnect plug from electrical outlet, disassemble the plug and interchange any
two power leads (not the green ground lead). Then reassemble the plug and recheck.
Produktspezifikationen
| Marke: | Hobart |
| Kategorie: | Fleischwolf |
| Modell: | 4822 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Hobart 4822 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Fleischwolf Hobart
24 August 2024
23 September 2023
23 September 2023
23 September 2023
23 September 2023
23 September 2023
23 September 2023
Bedienungsanleitung Fleischwolf
- ADE
- Fritel
- Panasonic
- WestBend
- OBH Nordica
- N8WERK
- Manta
- Zeegma
- Beem
- Melissa
- Livoo
- AFK
- Proficook
- Krups
- Lümme
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
9 Juni 2025
8 Juni 2025
6 Juni 2025