Hotpoint H7F HS51 X UK Bedienungsanleitung

Lies die bedienungsanleitung für Hotpoint H7F HS51 X UK (8 Seiten) kostenlos online; sie gehört zur Kategorie Spülmaschine. Dieses Handbuch wurde von 50 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 25.5 Bewertungen. Hast du eine Frage zu Hotpoint H7F HS51 X UK oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

ENDaily Reference Guide

1

CONTROL PANEL

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

register your appliance on: www.hotpoint.eu/register

Before using the appliance carefully read Safety

and Installation Instructions. More information about your product

available on website: docs.hotpoint.eu

After installation, please remember to remove all transport protection

parts from the dishwasher.

SETTING MENU

1. Switch on the appliance by pressing the button.ON-OFF

2. Hold the Settings (Half Load)button for 3 seconds until you hear

a beep.

3. After one second the rst available setting (letter „h”) will be displayed.

4. Press button to scroll through the list of available settings (see table

below), then press START/Pause to view and change the value of the

currently selected setting.

5. Press to change the value, then press START/Pause to save the

new value.

6. To change another setting, repeat points 2 and 5.

7. Press or wait 30 seconds to exit the menu.ON-OFF

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and the

machine’s functional components.

The salt reservoir is located in the lower part of the dishwasher (under the

lower rack on the left side).

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

• Salt must be lled when the SALT REFILL indicator light on the

control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel and ll the salt reservoir (see gure)

right up to its edge (approximately kg); it is not 0,5

unusual for a little water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly so that no detergent can get into

the container during the wash program (this could damage the water

softener beyond repair).

Run a program every time as soon as you completed relling the salt

reservoir to avoid corrosion.

Setting the water hardness

To allow the water softener to work in a perfect way, it is essential that the water

hardness setting is based on the actual water hardness in your house. This infor-

mation can be obtained from your local water supplier. The factory setting is “3”.

See „WATER HARDNESS TABLE”.

To change, follow instructions in section „SETTING MENU”.

LETTER SETTINGVALUES

(Default - )in bold

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”)1 | 2 | | 4 | 53

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF RINSE AID”)0 | 1 | 2 | 3 | 4 | 5

ActiveDry(see “OPTIONS AND FUNCTIONS”)

“1” = On, “0” = O1 | 0

Sound

“1” = On, “0” = O1 | 0

Factory Settings

Press START/Pauseto restore to the factory

default all the values of the settings included

in the settings menu.

-

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indicator

light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Use of salt is recommended with any type of dishwasher detergent.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently preventing

scale buildup on the heater, contributing also to better cleaning eciency.

This system regenerates itself with salt, therefore it is required to rell

the salt container when empty.The frequency of regeneration depends

on the water hardness level setting - regeneration takes place once per 4-6

Eco cycles with the water hardness level set to . The regeneration process 3

occurs at the beginning of the cycle with additional fresh water.

• Single regeneration consumes: ~3L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should be lled A

when the in the control panel is lit.RINSE AID REFILL indicator light

1. Open the dispenser B by

pressing and pulling up the

tab on the lid.

2. Pour in the rinse aid (max. 110

ml), making sure it does not

overow from the dispenser.

If this happens, clean the spill

immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

Adjusting the dosage of rinse aid

If you are not completely satised with the drying results, you can adjust

the quantity of rinse aid used.

To change, follow instructions in the section .„SETTING MENU”

If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW

RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of levels can be set according to the dishwasher model.6

• If you see bluish streaks on the dishes, set a low number (0-3).

• If there are drops of water or limescale marks on the dishes, set

a mid-range number (4-5).

A

B

FIRST TIME USE

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 (soft)0 - 60 - 100 - 7

2 (medium)7 - 1111 - 208 - 14

3 (average)12 - 1621 - 2915 - 20

4 (hard)17 - 3430 - 6021 - 42

5 (very hard)35 - 5061 - 9043 - 62

123456789101112131415 161718 19202122

1. ON-OFF/Resetbutton with indicator light

2. Eco program button with indicator light

3. Auto Intensive program button with indicator light

4. Auto Mixed program button with indicator light

5. Auto Fast program button with indicator light

6. Rapid program button with indicator light

7. Delicates

programbutton with indicator light

8. Soak programbutton with indicator light

9. Salt reservoir empty indicator light

10. Rinse Aid reservoir empty indicator light

11. Display

12. Program numberremaining time and indicator

13. Closedwater tap indicator light

14. DESCALE indicator light

15. 3D Zone Wash optionbutton with indicator light

16. Half Load optionSettings button with indicator light/ - 3 sec. press

17. Extra Dry option button with indicator light

18. Silent optionKey lock button with indicator light/ - 3 sec. press

19. Sani Rinse option button with indicator light

20. Self-Clean program button with indicator light

21. Delay optionbutton with indicator light

22. START/Pause button with indicator light

Produktspezifikationen