Hughes & Kettner ATS Sixty Bedienungsanleitung
Hughes & Kettner
Nicht kategorisiert
ATS Sixty
Lies die bedienungsanleitung für Hughes & Kettner ATS Sixty (6 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 4 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 2.5 Bewertungen. Hast du eine Frage zu Hughes & Kettner ATS Sixty oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6
ATS SIXTY
ADVANCED TUBE SYSTEM GUITAR COMBO
USER MANUAL
THF CL
FAN
CHANNEL:
The CLEAN channel on the ATS Sixty is constructed using solid state (transistor)
technology. This allows modern, sparkling clean sounds to be produced, like those
featured on many contemporary recordings. The traditional 3-band equalisation
section with passive tone controls also makes it possible to produce valve-like clean
sounds using the “SOFT CLICK” circuitry.
(2) VOLUME:
Volume adjusts the amplification level of the clean channel. Turned to position 8-9
you can achieve the crunchy “Soft Click” Sound. With pickups delivering more
output (humbuckers) this effect appears at lower volume settings
(5-6)
(3) BASS
/
MID /TREBLE:
The center frequency and bandwidth for each of this three controls has been
carefully selected to enable you to obtain a broad range of classic and modern clean
sounds. Start with a standard setting (all controls in 12‘0 clock position) and change
it as you want (f.e. more TREBLE for more harmonic overtones and sparkling clean
sounds).
(4) CHANNEL SELECT:
Switches the input signal either to the CLEAN or the OVERDRIVE channel. The
OVERDRIVE channel is active when the LED right of the channel select switch is
on.
T I P : A n y conventional
footswitch can be used to
change between CLEAN and
T U B E O V E R D R I V E
channels on the Sixty by
c o n n e c t i n g i t t o
t h e
FOOTSWITCH socket on
the rear panel.
TURF
OVERDRIVE
The Overdrive channel on the ATS Sixty consists of a genuine valve circuit (ECC
83). Valves produce a considerably better sound when overdriven than transistors.
The contour of the harmonic distortion and the distinctive compression effect are
the reasons why the authentic warm valve sound is sought after. However, valves do
have a couple of drawbacks!
2
TURF OVERDRIVE CHANNEL
Valves need to reach a specific operating temperature, which means that it
takes a few seconds after switching on before they are ready for use.
l
Valves are sensitive to shock. Allow the unit to cool off for a few minutes
before moving it.
The sound characteristics of valves do lend to change with age. You should
exchange your valves occasionally; the ECC 83 tubes used in the Sixty are
amongst the most frequently used and affordable types available. In normal
use, it should only be necessary to change the valves every few years.
(5) GAIN:
Adjusts the input sensivity of the TUBE circuitry and thereby the saturation. At
lower GAIN levels, you can achieve bluesy Clean and Crunch sounds.
In the specially marked high level section an automatic MID BOOST gets effective,
perfect for modern “hot rodded” Overdrive sounds.
The GAIN control influences the overdrive characteristics as well as the volume of
the TUBE OVERDRIVE channel. To alter the level, use the VOLUME control.
The TONE CONTROLS on the TUBE OVERDRIVE channel are active in
operation, and can therefore be used to boost specific frequency ranges. This can be
very useful for producing modern
“hot rodded” distortion sounds. The filter
characteristics of the two controls are chosen so as to make selection of the
distinctive “creamy” lead and riff sounds easier.
(6) VOICE:
Voice adjusts a wide range of lower mids and thus controls the overdrive
characteristic. More “Voice” will make your guitar sound more “creamy”.
(7)
BITE:
Bite controls the upper harmonics and the penetration of the guitar sound.
(8) VOLUME:
VOLUME adjusts the output volume of the TUBE OVERDRIVE and thus the
volume balance between CLEAN and OVERDRIVE.
3
Produktspezifikationen
| Marke: | Hughes & Kettner |
| Kategorie: | Nicht kategorisiert |
| Modell: | ATS Sixty |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Hughes & Kettner ATS Sixty benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Hughes & Kettner
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
13 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Jomox
- Karma
- Livoo
- Furrion
- Polyend
- Livarno
- Satco
- Alogic
- Liemke
- Aurora
- Sprolink
- Perma
- BABY Born
- Panduit
- Game Factor
Neueste Bedienungsanleitung für -Kategorien-
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025