Hunter Saddle Creek 19046 Bedienungsanleitung

Lies die bedienungsanleitung für Hunter Saddle Creek 19046 (2 Seiten) kostenlos online; sie gehört zur Kategorie Beleuchtung. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 3 Bewertungen. Hast du eine Frage zu Hunter Saddle Creek 19046 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION

For Models:

Para los Modelos:

Pour les Modèles:

Here are the

tools you’ll

need to

complete your

installation:

Estas son las

herramientas

que usted

necesitará para

completar su

instalación:

Voici les outils

dont vous

aurez besoin

pour réaliser

l’installation:

Ladder

Escalera

Échelle

Pliers

Alicates

Pince

Wire Strippers

Pelacables

Pince à dénuder

READ AND SAVE THESE INSTRUCTIONS

These instructions are provided for your safety. It

is very important that they are read carefully and

completely before beginning installation of the

lighting xture.

LEA Y GUARDE ESTAS INSTRUCCIONES

Estas instrucciones se proporcionan para su

seguridad. Es muy importante leerlas detenid-

amente y completamente antes de comenzar la

instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS

Ces instructions sont fournies pour votre sécurité.

Il est très important de les lire attentivement dans

leur intégralité avant d’entreprendre l’installation

du luminaire.

Fixture weight ±2 lbs:

Peso ±2 lb:

Poids xe ±2 lbs:

•

WARNING

• All wiring must be in accordance with national

and local electrical codes ANSI/NFPA 70. If you

are unfamiliar with wiring or in doubt, consult a

qualied electrician.

• To avoid possible electrical shock, before

installing your light xture, disconnect the power

by turning off the circuit breakers to the outlet box

associated with the wall switch location.

• The lighting xture must be grounded. If the

ground wire for the installation site is not present,

immediately STOP installation and consult a

qualied electrician.

• Todo el cableado debe realizarse de acuerdo con

los códigos eléctricos locales y nacionales ANSI/

NFPA 70. Si no está familiarizado con el cableado,

o si tiene duda, consulte a un electricista calicado.

• Para evitar una posible descarga eléctrica, antes

de instalar su lámpara, desconecte la energía

apagando los interruptores automáticos (breakers)

que alimentan la caja de salida asociada con la

ubicación del interruptor de pared.

•

ADVERTENCIA

• L’appareil d’éclairage doit être mis à la terre.

Si le l de terre du lieu d’installation n’est pas

présent, ARRÊTEZ immédiatement l’installation et

consultez un électricien qualié.

•

AVERTISSEMENT

•

Tout le câblage doit être conforme aux codes

électriques nationaux et locaux en vigueur et à la

norme ANSI/NFPA70. Si vous n'avez pas l'habitude

de faire ce câblage ou en cas de doute, adressez-

vous à un électricien qualié.

• Pour éviter tout choc électrique, avant d’installer

le luminaire, coupez le courant en éteignant les

disjoncteurs de la boîte électrique associée à

l’interrupteur mural.

•

Le luminaire doit être mis à la terre. Si le l

de terre du lieu d’installation n’est pas présent,

ARRÊTER immédiatement l’installation et

consulter un électricien qualié.

Part #/Pieza #/Pièce #

Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De

Maintenance Quincaillerie

Finish/Finish/FiniModel/Modelo/Modèle

Glass/Domo De Vidrio/Verre

Type/Tipo/Type

©2022 Hunter Fan Co.

Light Pendant / Semi-Flush

Luz Colgante / Semi-Empotrada

Lumière Chaînette / Semi Afeurant

Part #/Pieza #/Pièce #Model/Modelo/ Modèle

ENGLISH

NOTICE

In order to use a 12in rod by

itself you must rst remove

the post from the 6in rod and

install it on one of the ends of

the 12in rod.

Screwdriver

Destornilladore

Tournevis

Twist or tape wire ends

together to make it

easier to pass them

through the downrods.

Threaded post may also

be removed for easier

wire access.

Hunter Pro Tip:

J

M

H

I

A

B

C

D

E

F

G

K

L

N

O

P

Q

2

1

R

S

F

H

M

N

O

P

A

B

C

D

E

19026

19029

19032

19046

Saddle Creek

KG20902214

KG20901834

Brushed Nickel/Níquel Pulido/

Nickel Brossé

Noble Bronze/Bronce Noble/

Bronze Noble

19026

19029

19032

19046

KG21000136

KG21000046

Cased White Glass/Pantalla de

Vidrio Blanco/Verre Blanc

Clear Seeded Glass/Vidrio

Transparente Con Burbujas/

Verre Piqueté Transparent

19026

19032

19029

19046

ML279

r_031422

3.7 lbs(1.68 kg)

1

1

1

FINISHING THE INSTALLATION

CONNECTING THE WIRES

ASSEMBLING THE FIXTURE

PREPARING FOR INSTALLATION

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep

cleaning. For regular cleaning, turn off the light and wipe down the xture

with a clean lint-free cotton or microber cloth. Never spray cleaner directly

onto the xture.

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old xture

from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap

nuts (H) from mounting screws (A). Place the mounting plate (B) over the junction box so that mounting screws (A) and nuts

(C) extend out away from the ceiling. Adjust the position of mounting screws (A) so that mounting screws (A) can be exposed

5-6 mm after passing through the canopy (F) to properly t the cap nuts. Depending on the placement of your junction box the

position of mounting screws (A) may need to be adjusted to allow the canopy to be ush with the ceiling. Mounting screws (A)

can be adjusted by loosening nuts (C) and loosening or tightening mounting screws (A). Once the ideal position of mounting

screws (A) has been conrmed, tighten nuts (C) on mounting screws (A) on the front of the mounting plate to ensure that

mounting screws (A) are secure. Pull the house wires through the center of mounting plate (B). Secure mounting plate (B) to

the junction box by tightening the screws (D).

1. FOR PENDANT INSTALLATION:

There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each xture. Determine the correct number of rods needed for

proper hanging height. To lengthen the xture, add additional rods. To shorten the xture, trim the wires to desired length.

Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the xture’s wiring to discard.

Keep in mind that you must use at least one rod to hang the xture. Thread the wires through the rods and pull the wires until

taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening

of the downrods may be required). Screw rod onto threaded post (M) on the xture. Pull the xture wires through the top of the

canopy. Screw the top rod to hang straight (I) of canopy (F).

2. FOR SEMI-FLUSH INSTALLATION:

Unscrew the hex nut (Q) inside the canopy (F) and set hex nut (Q), and washers (R, S) aside. Remove the hang straight (I) from

the canopy (F). Pass the wires and threaded post of xture (M) through canopy (F) and secure it with the washer (S), washer (R)

and hex nut (Q) inside canopy (F).

Have a helper support the xture’s weight while completing the wiring.

Attach the xture’s wires to the power supply wires from the junction box.

Connect black to black (Live); white to white (grounded); grounding to

grounding (green or copper). Twist the ends of the wire pairs together.

Then, twist on a wire connector. Make sure all twists are in the same

direction. Loop xture’s ground wire around grounding screw (E) and

tighten. If there is no ground wire (green or copper) from the junction box,

contact a qualied electrician.

Raise canopy (F) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of canopy

(F). Secure canopy (F) in place with cap nuts (H). Install light bulb (not included) in accordance with the xture’s specications.

Do not exceed the recommended wattage. Secure glass (P) onto the socket (N) with screws (O). Your installation is now

complete. Turn on the power and test.

Produktspezifikationen